| 品牌 | 克拉 | 型號 | rxg |
| 種類 | 線繞 | 性能 | 通用 |
| 材料 | 線繞 | 工藝 | 普通線繞 |
| 外形 | a | 標稱阻值 | a |
| 溫度系數 | a | 額定功率 | %(w) |
| 調節方式 | 固定 | 功率特性 | 大功率 |
| 營銷方式 | 直銷 | 產品性質 | 熱銷 |
產品名稱:rxg被漆線繞電阻器
product name: rxg silicon cemented wire wound resistors
型 號:rxg
type: rxg
產品介紹:rxg型涂料繞線電阻器其表面覆蓋了具有阻燃,耐高溫特性的涂料,性能可靠,使用方便等特點。電阻分為固定式或可調式,可調式可左右移動。固定式有兩個或多個電阻腳,電阻腳厚度可根據功率大小調節。
product introduction: rxg series cement-coated wire wound resistor is covered with dope which has inflammability and can resistance to high temperature, it has the characteristic of good ability and easy to use. the resistor can be classed to settled form and adjustive form, and the adjustive form can move right-and-left. the settled form has two or more terminals, its thickness can adjust accord to power.
用 途:涂料繞線電阻廣泛用于變頻器制動,電梯,起重機械以及負載電阻之用。
purpose: cement-coated wire wound resistor is used in transducer trig, elevator, derrick and as load resistor widely.
■電氣及機械特性 electrical and mechanical specifications
特性 | 規格 | 試驗方法 |
阻值及阻值允許偏差 | 1ω≤r±5%(j) , 1ω>r±10%(k) | jis-c-5202 5-1 |
額定負荷 | 表面最高溫度: 5~200w≤275℃ | jis-c-5202 5-4 |
短時過負荷 | 無可見損傷,δr≤±(2%r+0.05ω) | jis-c-5202 5-5 10倍 5秒 |
絕緣電阻 | r≥100mω 1min | jis-c-5202 5-6 dc500v |
耐電壓 | 無可見損傷,無飛弧擊穿 δr≤±(0.1%r+0.05ω) | jis-c-5202 5-7 |
電阻溫度特性 | ±260ppm/℃ | jis-c-5202 5-2 b |
端子強度 | 無松動或機械損傷 | jis-c-5202 6-1(2) |
電阻體強度 | 無可見損傷 | jis-c-5202 6-2 |
耐振性 | 無可見損傷,δr≤±(0.1%r+0.05ω) | jis-c-5202 6-3 |
可焊性 | 新焊錫覆蓋率為95%以上 | jis-c-5202 6-5 |
■環境特性 environmental specifications
特性 | 規格值 | 試驗方法 |
耐熱性 | 除端子外無明顯變色和損傷,標志清晰 | jis-c-5202 7-2 |
熱沖擊 | 無可見機械損傷 | jis-c-5202 7-3 |
耐濕性 | 無可見損傷,標志清晰,δr≤±(3%r+0.05ω),絕緣電阻≥10mω | jis-c-5202 7-5 dc100 40℃ 95%rh 500hours |
耐久性 (額定負載) | 外觀無可見損傷,標志清晰,δr≤±(3%r±0.05ω) | jis-c-5202 7-10 100%負荷 rated power load 90 min on 30 min off 500hours |
■規格 specification
外型、尺寸 configuration (m/m)
rxg type
● 型號說明 type explanation
rxg為被漆繞線固定電阻器,rxg(t)為被漆繞線可調電阻器
rxg is the wire-wound cement-coating fixed resistor
rxg(t)is the wire-wound cement-coating adjustable resistor
● 結構說明 structure explanation
rxg-a、rxg(t)-a為電阻體與安裝支架之間不用瓷片隔離。
rxg-a、rxg(t)-a not using the porcelain sheet to separate the resistor body from the installation frame.
rxg-b、rxg(t)-b為電阻體與安裝支架之間使用瓷片隔離。
rxg-b、rxg(t)-b using the porcelain sheet to separate the resistor body from the installation frame.
rxg-d型為電阻體兩端使用瓷片并在中間串一根螺栓。
rxg-d using the porcelain sheet on both of the two terminals and they are
series-connected by a screw bolt.