- 您現在的位置：買賣IC網 > PDF目錄373917 > AD7810YN (ANALOG DEVICES INC) 2.7 V to 5.5 V, 2 us, 10-Bit ADC in 8-Lead microSOIC/DIP PDF資料下載
參數資料
| 型號： | AD7810YN |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | ADC |
| 英文描述： | 2.7 V to 5.5 V, 2 us, 10-Bit ADC in 8-Lead microSOIC/DIP |
| 中文描述： | 1-CH 10-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDIP8 |
| 封裝： | 0.300 INCH, MINI, PLASTIC, DIP-8 |
| 文件頁數： | 9/11頁 |
| 文件大小： | 142K |
| 代理商： | AD7810YN |
AD7810
–9–
REV. A
t
POWER-UP
m
A
B
D
OUT
SCLK
t
1
CONVST
CURRENT CONVERSION RESULT
Figure 15. Mode 2 Operation Timing
Mode 2 Operation (Automatic Power-Down)
When used in this mode of operation, the part automatically
powers down at the end of a conversion. This is achieved by
leaving the
CONVST
signal low until the end of the conversion.
Because it takes approximately 1
μ
s for the part to power up
after it has been powered down, this mode of operation is in-
tended to be used in applications where slower throughput rates
are required, i.e., in the order of 100 kSPS. The timing diagram
in Figure 15 shows how to operate the part in this mode. If the
AD7810 is powered down, the rising edge of the
CONVST
pulse causes the part to power up. When the part has powered
up (
≈
1
μ
s after the rising edge of
CONVST
), the
CONVST
signal is brought low, and a conversion is initiated on this falling
edge of the
CONVST
signal. The conversion takes 2
μ
s and
after this time, the conversion result is latched into the serial
shift register and the part powers down. Therefore, when the
part is operated in Mode 2, the effective conversion time is
equal to the power-up time (1
μ
s) and the SAR conversion time
(2
μ
s).
NOTE: Although the AD7810 takes 1
μ
s to power up after the
rising edge of
CONVST
, it is not necessary to leave
CONVST
high for 1
μ
s after the rising edge before bringing it low to ini-
tiate a conversion. If the
CONVST
signal goes low before 1
μ
s in
time has elapsed, then the power-up time is timed out internally
and a conversion is then initiated. Hence the AD7810 is guaran-
teed to have always powered up before a conversion is initiated—
even if the
CONVST
pulse width is < 1
μ
s. If the
CONVST
width
is > 1
μ
s, then a conversion is initiated on the falling edge.
As in the case of Mode 1 operation, the rising edge of the
CONVST
pulse enables the serial port of the AD7810 (see
Serial Interface section). If a serial read is initiated soon after
this rising edge (Point “A”), i.e., before the end of the conver-
sion, the result of the previous conversion is shifted out on pin
D
OUT
. In order to read the result of the current conversion, the
user must wait at least 2
μ
s after the falling edge of
CONVST
before initiating a serial read. The serial port of the AD7810 is
still functional even though the AD7810 has been powered down.
NOTE: Serial read should not cross the next rising edge of
CONVST
.
Because it is possible to do a serial read from the part while it
is powered down, the AD7810 is powered up only to do the
conversion and is immediately powered down at the end of a
conversion. This significantly improves the power consumption
of the part at slower throughput rates—see Power vs. Through-
put Rate section.
SERIAL INTERFACE
The serial interface of the AD7810 consists of three wires, a
serial clock input SCLK, serial port enable
CONVST
and a
serial data output D
OUT
(see Figure 16). The serial interface
is designed to allow easy interfacing to most microcontrollers,
e.g., PIC16C, PIC17C, QSPI and SPI, without the need for any
gluing logic. When interfacing to the 8051, the SCLK must be
inverted. The Microprocessor Interface section explains how to
interface to some popular microcontrollers.
Figure 16 shows the timing diagram for a serial read from the
AD7810. The serial interface works with both a continuous and
a noncontinuous serial clock. The rising edge of the
CONVST
signal
resets
a counter, which counts the number of serial clocks
to ensure the correct number of bits are shifted out of the serial
shift registers. The SCLK is ignored once the correct number of
bits have been shifted out. In order for another serial transfer to
take place, the counter must be reset by the falling edge of the
10th SCLK. Data is clocked out from the D
OUT
line on the first
rising SCLK edge after the rising edge of the
CONVST
signal
and on subsequent SCLK rising edges. D
OUT
enters its high
impedance state again on the falling edge of the 10th SCLK.
In multipackage applications, the
CONVST
signal can be used
as a chip select signal. The serial interface will not shift data out
until it receives a rising edge on the
CONVST
pin.
CONVST
D
OUT
SCLK
t
8
1
2
3
4
5
6
7
8
9
10
DB7
DB6
DB5
DB4
DB3
DB2
DB1
DB0
DB9
DB8
t
3
t
4
t
7
t
6
t
5
Figure 16. AD7810 Serial Interface Timing
相關PDF資料 |
PDF描述 |
|---|---|
| AD7810YR | ECONOLINE: REC2.2-S_DR/H1 - 2.2W DIP Package- 1kVDC Isolation- Regulated Output- UL94V-0 Package Material- Continuous Short Circiut Protection- Internal SMD design- 100% Burned In- Efficiency to 75% |
| AD7813YRU | +2.7 V to +5.5 V, 400 kSPS 8-/10-Bit Sampling ADC |
| AD7813YN | +2.7 V to +5.5 V, 400 kSPS 8-/10-Bit Sampling ADC |
| AD7813YR | +2.7 V to +5.5 V, 400 kSPS 8-/10-Bit Sampling ADC |
| AD7816AR-REEL | Low Cost, High Speed Rail-to-Rail Amplifier (Single); Package: SOIC; No of Pins: 8; Temperature Range: TBD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7810YNZ | 功能描述:IC ADC 10BIT SRL HS LP 8DIP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6 |
| AD7810YR | 功能描述:IC ADC 10BIT 2.7V 8-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 位數:12 采樣率（每秒）:3M 數據接口:- 轉換器數目:- 功率耗散（最大）:- 電壓電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-23-6 包裝:帶卷 (TR) 輸入數目和類型:- |
| AD7810YRM | 制造商:Analog Devices 功能描述:ADC Single SAR 350ksps 10-bit Serial 8-Pin MSOP 制造商:Rochester Electronics LLC 功能描述:10-BIT SERIAL SINGLE ADC I.C. - Bulk |
| AD7810YRM-REEL | 制造商:Analog Devices 功能描述:ADC Single SAR 350ksps 10-bit Serial 8-Pin MSOP T/R |
| AD7810YRM-REEL7 | 制造商:Analog Devices 功能描述:ADC Single SAR 350ksps 10-bit Serial 8-Pin MSOP T/R |
發布緊急采購，3分鐘左右您將得到回復。