- 您現在的位置：買賣IC網 > PDF目錄373917 > AD7821 (Analog Devices, Inc.) LC2MOS High Speed, μP-Compatible 8-Bit ADC with Track/Hold Function(帶跟蹤/保持功能,LC2MOSμP兼容8位高速A/D轉換器) PDF資料下載
參數資料
| 型號： | AD7821 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | LC2MOS High Speed, μP-Compatible 8-Bit ADC with Track/Hold Function(帶跟蹤/保持功能,LC2MOSμP兼容8位高速A/D轉換器) |
| 中文描述： | LC2MOS高速，微處理器兼容的8位ADC的采樣/保持功能（帶跟蹤/保持功能，LC2MOSμP兼容8位高速的A / D轉換器） |
| 文件頁數： | 10/12頁 |
| 文件大小： | 263K |
| 代理商： | AD7821 |
AD7821
REV. A
–10–
MICROPROCE SSOR INT E RFACING
T he AD7821 is designed for easy interfacing to microprocessors
as a memory mapped peripheral or an I/O device. T his reduces
to a minimum the amount of external logic required for
interfacing.
AD7821 – 68008 INT E RFACE
Figure 14 shows an AD7821 interface to the 68008 micropro-
cessor. T he ADC is configured for the RD interface mode. T his
means that one read instruction starts a conversion and reads
the result when the conversion is completed. T he read cycle is
stretched out over the entire conversion period by taking the
INT
line back to the
DTACK
input of the 68008. Starting a
conversion and reading the relevant data consists of a <MOVE
B Dn, addr> instruction, where addr is the decoded ADC ad-
dress and Dn is the data register into which the result is placed.
Figure 14. AD7821 to 68008 Interface
AD7821 – 8088 INT E RFACE
A typical interface to the 8088 is shown in Figure 15. T he
AD7821 is configured for the
RD
interface mode. One read in-
struction starts a conversion and reads the result. T he read cycle
is stretched out over the entire conversion period by taking the
RDY line back to the READY input of the 8088. Starting a con-
version and reading the result consists of a <MOV AX , (addr)>
instruction, where addr is the decoded ADC address and AX is
the 8088 data register into which the conversion result is placed.
Figure 15. AD7821 to 8088 Interface
AD7821 – T MS32010 INT E RFACE
A typical interface to the T MS32010 is shown in Figure 16. T he
AD7821 is mapped at a port address and the interface is designed
for the maximum T MS32010 clock frequency of 20 MHz. In this
case, the AD7821 is configured in the WR-RD interface mode.
T his means that a write instruction starts a conversion and a
read instruction reads the result when the conversion is com-
pleted. A precise timer or clock source is used to start a conver-
sion in applications requiring equidistant sampling intervals.
T he scheme used, whereby the AD7821 generates an interrupt
to the T MS32010, is limited in that it does not allow the
AD7821 to be sampled at its maximum rate. T his is because the
time between samples has to be long enough to allow the
T MS32010 to service its interrupt and read data from the
AD7821. Constant interruption of the T MS32010 by the
AD7821, every time the ADC completes a conversion, is not a
very efficient use of the processor time. T o overcome these
problems, some buffer memory or FIFO could be placed be-
tween the AD7821 and the T MS32010. T he
INT
line of the
AD7821 could be used to trigger a pulse which drives its
CS
and
RD
lines and places the AD7821 data into a FIFO or buffer
memory. T he microprocessor can then read a batch of data
from the FIFO or buffer memory at some convenient time.
Reading data from the AD7821, after an
INT
has been re-
ceived, consists of <IN A, PA> instruction (PA is the decoded
ADC address).
Figure 16. AD7821 to TMS32010 Interface
AD7821 – 8051 INT E RFACE
Figure 17 shows the AD7821 interface to the 8051 microcom-
puter. T he AD7821 is configured in the WR-RD interface mode
and is connected to the 8051 ports. T he processor starts conver-
sion and then polls
INT
, until it goes low, before reading the
conversion result. Data is read from the AD7821 by using the
<MOV A, 90H> instruction (90H is the address for Port 1).
Figure 17. AD7821 to 8051 Interface
相關PDF資料 |
PDF描述 |
|---|---|
| AD7823YRM | 2.7 V to 5.5 V, 4.5 us, 8-Bit ADC in 8-Lead microSOIC/DIP |
| AD7823YN | 1.2V, 12 Bit 200KSPS, Serial ADC 6-SOT-23 -40 to 85 |
| AD7823YR | 1.2V, 12 Bit 200KSPS, Serial ADC 6-SOT-23 -40 to 85 |
| AD7825 | 3 V/5 V, 2 MSPS, 8-Bit, 1-, 4-, 8-Channel Sampling ADCs |
| AD7825BN | 3 V/5 V, 2 MSPS, 8-Bit, 1-, 4-, 8-Channel Sampling ADCs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7821BQ | 功能描述:IC ADC 8BIT HS TRACK/HOLD 20CDIP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD7821KN | 功能描述:IC ADC 8BIT LC2MOS T/H HS 20-DIP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7821KNZ | 功能描述:IC ADC 8BIT LC2MOS T/H HS 20-DIP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7821KNZ | 制造商:Analog Devices 功能描述:IC 8-BIT ADC |
| AD7821KP | 制造商:AD 制造商全稱:Analog Devices 功能描述:LC2MOS High Speed, mP-Compatible 8-Bit ADC with Track/Hold Function |
發布緊急采購，3分鐘左右您將得到回復。