- 您現在的位置：買賣IC網 > PDF目錄363899 > W78IE52 (WINBOND ELECTRONICS CORP) 8 BIT MICROCONTROLLER PDF資料下載
參數資料
| 型號： | W78IE52 |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8 BIT MICROCONTROLLER |
| 中文描述： | 8-BIT, FLASH, 20 MHz, MICROCONTROLLER, PDIP40 |
| 封裝： | DIP-40 |
| 文件頁數： | 9/22頁 |
| 文件大小： | 281K |
| 代理商： | W78IE52 |
Preliminary W78IE52
Publication Release Date: April 20, 2005
- 9 -
Revision A2
Reset
The external RESET signal is sampled at S5P2. To take effect, it must be held high for at least two
machine cycles while the oscillator is running. An internal trigger circuit in the reset line is used to
deglitch the reset line when the W78IE52 is used with an external RC network. The reset logic also
has a special glitch removal circuit that ignores glitches on the reset line.
During reset, the ports are initialized to FFH, the stack pointer to 07H, PCON (with the exception of bit
4) to 00H, and all of the other SFR registers except SBUF to 00H. SBUF is not reset.
7. ON-CHIP FLASH EPROM CHARACTERISTICS
The W78IE52 has several modes to program the on-chip Flash EPROM. All these operations are
configured by the pins RST, ALE, PSEN , A9CTRL (P3.0), A13CTRL (P3.1), A14CTRL (P3.2),
OECTRL (P3.3), CE
(P3.6), OE
(P3.7), A0 (P1.0) and V
PP
(EA ). Moreover, the A15
A0 (P2.7
P2.0, P1.7
P1.0) and the D7
D0 (P0.7
P0.0) serve as the address and data bus respectively for
these operations.
Read Operation
This operation is supported for customer to read their code and the Security bits. The data will not be
valid if the Lock bit is programmed to low.
Output Disable Condition
When the
OE
is set to high, no data output appears on the D7..D0.
Program Operation
This operation is used to program the data to Flash EPROM and the security bits. Program operation
is done when the V
PP
is reach to V
CP
(12.5V) level, CE set to low, and OE set to high.
Program Verify Operation
All the programming data must be checked after program operations. This operation should be
performed after each byte is programmed; it will ensure a substantial program margin.
Erase Operation
An erase operation is the only way to change data from 0 to 1. This operation will erase all the Flash
EPROM cells and the security bits from 0 to 1. This erase operation is done when the V
PP
is reach to
V
EP
level, CE set to low, and OE set to high.
Erase Verify Operation
After an erase operation, all of the bytes in the chip must be verified to check whether they have been
successfully erased to 1 or not. The erase verify operation automatically ensures a substantial erase
margin. This operation will be done after the erase operation if V
PP
= V
EP
(14.5V),
CE
is high and
OE is low.
相關PDF資料 |
PDF描述 |
|---|---|
| W78IE54 | 8-BIT MTP Monitor Microcontroller(多次可編程的8位的監視微控制器) |
| W78IE54P | 8-BIT MTP MICROCONTROLLER |
| W78IRD2 | 8-BIT MICROCONTROLLER |
| W78IRD2A | 8-BIT MICROCONTROLLER |
| W78L052A | 8-BIT MICROCONTROLLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W78IE52_06 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-BIT MICROCONTROLLER |
| W78IE54 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-BIT MTP MICROCONTROLLER |
| W78IE54P | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-BIT MTP MICROCONTROLLER |
| W78IRD2 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-BIT MICROCONTROLLER |
| W78IRD2A | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-BIT MICROCONTROLLER |
發布緊急采購，3分鐘左右您將得到回復。