国产精品成人VA在线观看-国产乱妇乱子视频在播放-国产日韩精品一区二区三区在线-国模精品一区二区三区

參數資料
型號： W83697SF
廠商： WINBOND ELECTRONICS CORP
元件分類： 外設及接口
英文描述： WINBOND I/O
中文描述： MULTIFUNCTION PERIPHERAL, PQFP128
封裝： PLASTIC, QFP-128
文件頁數： 87/167頁
文件大小： 1094K
代理商： W83697SF
W83697HF/F
Publication Release Date: Feb. 2002
Revision 0.70
- 78 -
6.3.15 DMA Transfers
DMA transfers are always to or from the ecpDFifo, tFifo, or CFifo. The DMA uses the standard PC DMA
services. The ECP requests DMA transfers from the host by activating the PDRQ pin. The DMA will
empty or fill the FIFO using the appropriate direction and mode. When the terminal count in the DMA
controller is reached, an interrupt is generated and serviceIntr is asserted, which will disable the DMA.
6.3.16 Programmed I/O (NON-DMA) Mode
The ECP or parallel port FIFOs can also be operated using interrupt driven programmed I/O.
Programmed I/O transfers are to the ecpDFifo at 400H and ecpAFifo at 000H or from the ecpDFifo
located at 400H, or to/from the tFifo at 400H. The host must set the direction, state, dmaEn = 0 and
serviceIntr = 0 in the programmed I/O transfers.
The ECP requests programmed I/O transfers from the host by activating the IRQ pin. The programmed
I/O will empty or fill the FIFO using the appropriate direction and mode.
6.4 Extension FDD Mode (EXTFDD)
In this mode, the W83627HF changes the printer interface pins to FDC input/output pins, allowing the
user to install a second floppy disk drive (FDD B) through the DB-25 printer connector. The pin
assignments for the FDC input/output pins are shown in Table 6-1.
After the printer interface is set to EXTFDD mode, the following occur:
(1) Pins MOB# and DSB# will be forced to inactive state.
(2) Pins DSKCHG#, RDATA#, WP#, TRAK0#, INDEX# will be logically ORed with pins PD4-PD0 to
serve as input signals to the FDC.
(3) Pins PD4-PD0 each will have an internal resistor of about 1K ohm to serve as pull-up resistor for FDD
open drain/collector output.
(4) If the parallel port is set to EXTFDD mode after the system has booted DOS or another operating
system, a warm reset is needed to enable the system to recognize the extension floppy drive.
6.5 Extension 2FDD Mode (EXT2FDD)
In this mode, the W83627HF changes the printer interface pins to FDC input/output pins, allowing the
user to install two external floppy disk drives through the DB-25 printer connector to replace internal
floppy disk drives A and B. The pin assignments for the FDC input/output pins are shown in Table6-1.
After the printer interface is set to EXTFDD mode, the following occur:
(1) Pins MOA#, DSA#, MOB#, and DSB# will be forced to inactive state.
(2) Pins DSKCHG#, RDATA#, WP#, TRAK0#, and INDEX# will be logically ORed with pins PD4-PD0 to
serve as input signals to the FDC.
(3) Pins PD4-PD0 each will have an internal resistor of about 1K ohm to serve as pull-up resistor for FDD
open drain/collector output.
(4) If the parallel port is set to EXT2FDD mode after the system has booted DOS or another operating
system, a warm reset is needed to enable the system to recognize the extension floppy drive.
相關PDF資料
PDF描述
W83757 SUPER I/O CHIP
W83759 ADVANCED VL-IDE DISK CONTROLLER
W83759A ADVANCED VL-IDE DISK CONTROLLER
W83768 I/O COUPLER
W83769 LOCAL BUS IDE SOLUTION
相關代理商/技術參數
參數描述
W83697UF 制造商:WINBOND 制造商全稱:Winbond 功能描述:LPC I/O
W83697UG 功能描述:IC LPC SUPER I/O 128-PQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA，便攜式音頻/視頻，智能電話 接口:I²C，2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2
W83757 制造商:WINBOND 制造商全稱:Winbond 功能描述:SUPER I/O CHIP
W83759 制造商:WINBOND 制造商全稱:Winbond 功能描述:ADVANCED VL-IDE DISK CONTROLLER
W83759A 制造商:WINBOND 制造商全稱:Winbond 功能描述:ADVANCED VL-IDE DISK CONTROLLER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*