- 您現在的位置：買賣IC網 > PDF目錄363910 > W9967BCF (WINBOND ELECTRONICS CORP) JPEG USB Camera Chip(運用JPEG壓縮技術和通用串行總線結構技術的照相電路數字處理芯片的攝像照相機接口控制器) PDF資料下載
參數資料
| 型號： | W9967BCF |
| 廠商： | WINBOND ELECTRONICS CORP |
| 英文描述： | JPEG USB Camera Chip(運用JPEG壓縮技術和通用串行總線結構技術的照相電路數字處理芯片的攝像照相機接口控制器) |
| 中文描述： | USB相機的JPEG芯片（運用的JPEG壓縮技術和通用串行總線結構技術的照相電路數字處理芯片的攝像照相機接口控制器） |
| 文件頁數： | 34/72頁 |
| 文件大小： | 756K |
| 代理商： | W9967BCF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁當前第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁
W9967BCF
- 34 -
7.6 Power Management
The W9967BCF provides three output pins as described below for the video camera power
management to meet the USB specification requirements.
PWRDWN/PWRDWN#
: These pins, when active, are used to turn off the USB 5V power
supply to the video source circuits (CCD/CMOS sensor device, ADC, DSP, video decoder,
etc.).
SUSPND
: This pin, when active, is used to turn off the 3.3V power supply to the W9967BCF
(excluding USBVDD pin, the power supply for the transceiver), DRAM, and E
2
PROM.
Bit 10 of the Miscellaneous Control register (CR00) determines whether the W9967BCF-based device
is a high power device or a low power device as described below:
CR00_10 = 1
: High power, bus-powered devices. They must draw no more than 100 mA
upon power up and may draw up to 500 mA after being configured.
CR00_10 = 0
: Low power, bus-powered devices. May draw up to 100 mA from their upstream
connection to allow the interface to function when the remainder of the hub is powered down.
7.6.1 W9967BCF Reset
The W9967BCF has two reset sources: system reset from the input RSTIN# pin, and the USB reset
detected by seeing a single-ended zero (SE0) for more than 2.5 us. All reset sources are joined inside
the W9967BCF into a single reset signal which initializes the W9967BCF and is also output via the
RSTOUT pin to initialize other external circuits.
Reset can wake the W9967BCF from the suspended mode (SUSPND is inactive low) and turn off the
USB 5V power supply to the video source circuits (PWRDWN is active high and PWRDWN# is active
low).
7.6.2 Before Configured
Before configured, the W9967BCF should be reset and keep PWRDWN and PWRDWN# to be active
(CR00_4 = 0) such that the W9967BCF-based devices will not draw more than 100 mA from the USB
bus power supply. It is required that an external power-on reset should be applied to the RSTIN# pin
before any USB transaction is sent to the W9967BCF by the host.
7.6.3 After Configured
After configured, PWRDWN and PWRDWN# pins should be inactive by programming the Camera
Power-on Control register to one (CR00_4 = 1) to enable device functions. The W9967BCF-based
devices must draw less than 100 mA (CR00_10 = 0) or 500 mA (CR00_10 = 1) from the bus during
normal operation. The SOF (Start of Frame) packet is guaranteed to occur once a frame to keep full
speed devices awake during normal bus operation.
7.6.4 Suspend
The W9967BCF goes into the suspend mode from any powered state when it sees a constant idle state
on the USB bus lines for more than 3.0 ms. When suspended, both SUSPND and PWRDWN are active
相關PDF資料 |
PDF描述 |
|---|---|
| W9967CF | JPEG USB Camera Chip(運用JPEG壓縮技術和通用串行總線結構技術的照相電路數字處理芯片的攝像照相機接口控制器) |
| W99681CF | JPEG USB Dual Mode Camera Chip(運用JPEG壓縮技術、通用串行總線結構技術、雙制式的照相電路數字處理芯片的攝像照相機接口控制器) |
| W9971CF | Integrated Video Graphics Accelerator(集成的視頻圖形加速器) |
| W9980 | Digital Voice Recorder(數字式錄音器) |
| WA08-2433A | 820-980 MHz LOW NOISE BALANCE AMPLIFIER WA08-2433A |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W99681CF | 制造商:WINBOND 制造商全稱:Winbond 功能描述:JPEG USB Dual Mode Camera Chip |
| W99685 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| W99685BS | 制造商:WINBOND 制造商全稱:Winbond 功能描述:SYSTEM CAMERA DEVICE |
| W99685FS | 制造商:WINBOND 制造商全稱:Winbond 功能描述:SYSTEM CAMERA DEVICE |
| W9968CF | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Digital Camera |
發布緊急采購，3分鐘左右您將得到回復。