- 您現在的位置：買賣IC網 > PDF目錄373917 > AD7790B (Analog Devices, Inc.) Low Power, 16-Bit Buffered Sigma-Delta ADC PDF資料下載
參數資料
| 型號： | AD7790B |
| 廠商： | Analog Devices, Inc. |
| 元件分類： | ADC |
| 英文描述： | Low Power, 16-Bit Buffered Sigma-Delta ADC |
| 中文描述： | 低功耗，16位緩沖Σ-Δ模數轉換器 |
| 文件頁數： | 11/20頁 |
| 文件大小： | 299K |
| 代理商： | AD7790B |
AD7790
STATUS REGISTER (RS1, RS0 = 0, 0; POWER-ON/RESET = 0x88)
The status register is an 8-bit read-only register. To access the ADC status register, the user must write to the communications register,
select the next operation to be a read, and load bits RS1 and RS0 with 0. Table 8 outlines the bit designations for the status register. SR0
through SR7 indicate the bit locations, SR denoting the bits are in the status register. SR7 denotes the first bit of the data stream. The
number in brackets indicates the power-on/reset default status of that bit.
Rev. 0 | Page 11 of 20
SR7
RDY(1)
Table 8. Status Register Bit Designations
Bit Location
Bit Name
SR7
RDY
SR6
ERR(0)
SR5
0(0)
SR4
0(0)
SR3
1(1)
SR2
WL(0)
SR1
CH1(0)
SR0
CH0(0)
Description
Ready bit for ADC.
Cleared
when data is written to the ADC data register. The RDY bit is
set
automatically
after the ADC data register has been read or a period of time before the data register is updated with a
new conversion result to indicate to the user not to read the conversion data. It is also
set
when the part
is placed in powe-down mode. The end of a conversion is indicated by the DOUT/RDY pin also. This pin
can be used as an alternative to the status register for monitoring the ADC for conversion data.
ADC Error Bit. This bit is written to at the same time as the RDY bit.
Set
to indicate that the result written
to the ADC data register has been clamped to all 0s or all 1s. Error sources include overrange,
underrange.
Cleared
by a write operation to start a conversion.
This bit is automatically
cleared
.
This bit is automatically
cleared
.
This bit is automatically
set
.
This bit is automatically
cleared
if the device is an AD7790. It can be used to distinguish between the
AD7790 and AD7791, in which the bit is
set
.
These bits indicate which channel is being converted by the ADC.
SR6
ERR
SR5
SR4
SR3
SR2
0
0
1
0
SR1–SR0
CH1–CH0
MODE REGISTER (RS1, RS0 = 0, 1; POWER-ON/RESET = 0x02)
The mode register is an 8-bit register from which data can be read or to which data can be written. This register is used to configure the
ADC for range, enable or disable the buffer, or place the device into power-down mode. Table 9 outlines the bit designations for the mode
register. MR0 through MR7 indicate the bit locations, MR denoting the bits are in the mode register. MR7 denotes the first bit of the data
stream. The number in brackets indicates the power-on/reset default status of that bit. Any write to the setup register resets the modulator
and filter and sets the RDY bit.
MR7
MD1(0)
Table 9. Mode Register Bit Designations
Bit Location
Bit Name
MR7–MR6
MD1–MD0
MR6
MD0(0)
MR5
G1(0)
MR4
G0(0)
MR3
BO(0)
MR2
0(0)
MR1
BUF(1)
MR0
0(0)
Description
Mode Select Bits. These bits select between continuous conversion mode, single conversion mode, and
standby mode. In continuous conversion mode, the ADC continuously performs conversions and places
the result in the data register. RDY goes low when a conversion is complete. The user can read these
conversions by placing the device in continuous read mode whereby the conversions are automatically
placed on the DOUT line when SCLK pulses are applied. Alternatively, the user can instruct the ADC to
output the conversion by writing to the communications register. After power-on, the first conversion is
available after a period 2/ f
ADC
while subsequent conversions are available at a frequency of f
ADC
. In single
conversion mode, the ADC is placed in power-down mode when conversions are not being performed.
When single conversion mode is selected, the ADC powers up and performs a single conversion, which
occurs after a period 2/f
ADC
. The conversion result in placed in the data register, RDY goes low, and the
ADC returns to power-down mode. The conversion remains in the data register and RDY remains active
(low) until the data is read or another conversion is performed. See Table 10.
Range Bits. The AD7790 can be operated with four analog input ranges (see Table 11).
Burnout Current Enable Bit. When this bit is set to 1 by the user, the 100 nA current sources in the signal
path are enabled. When BO = 0, the burnout currents are disabled. The burnout currents can be enabled
only when the buffer is active.
MR5–MR4
MR3
G1–G0
BO
相關PDF資料 |
PDF描述 |
|---|---|
| AD7790BRM | Low Power, 16-Bit Buffered Sigma-Delta ADC |
| AD7790BRM-REEL | Low Power, 16-Bit Buffered Sigma-Delta ADC |
| AD7801BR | +2.7 V to +5.5 V, Parallel Input, Voltage Output 8-Bit DAC |
| AD7801BRU | +2.7 V to +5.5 V, Parallel Input, Voltage Output 8-Bit DAC |
| AD7801 | +2.7 V to +5.5 V, Parallel Input, Voltage Output 8-Bit DAC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7790BRM | 功能描述:IC ADC 16BIT BUFFERED LP 10MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| AD7790BRM-REEL | 制造商:Analog Devices 功能描述:ADC Single Delta-Sigma 120sps 16-bit Serial 10-Pin MSOP T/R 制造商:Analog Devices 功能描述:ADC SGL DELTA-SIGMA 0.12KSPS 16BIT SERL 10MSOP - Tape and Reel |
| AD7790BRMZ | 功能描述:IC ADC 16BIT SIGMA-DELTA 10-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| AD7790BRMZ | 制造商:Analog Devices 功能描述:IC 24-BIT ADC |
| AD7790BRMZ-REEL | 功能描述:IC ADC 16BIT SIGMA-DELTA 10-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
發布緊急采購，3分鐘左右您將得到回復。