国产精品成人VA在线观看-国产乱妇乱子视频在播放-国产日韩精品一区二区三区在线-国模精品一区二区三区

參數資料
型號： W3020
英文描述： GSM Multiband RF Transceiver
中文描述： 手機多頻段射頻收發器
文件頁數： 12/44頁
文件大小： 409K
代理商： W3020
Advance Data Sheet
December 1999
W3020 GSM Multiband RF Transceiver
12
Lucent Technologies Inc.
IF/Baseband Amplifier
The IF amplifier is a balanced-input/balanced-output
type and is connected to a balanced SAW filter. It
consists of three gain stages: an IF amplifier and two
sections of baseband amplifiers. The gain can be
changed in steps of 32, 16, 8, and 4 dB. The base-
band also contains a level-shifter stage to drive an
A/D converter directly. The level-shifter stage has 21
dB of gain that can be switched off. The specifications
below are for the two modes of operation.
The gain of the IF section is programmed via the
three-wire serial bus.
The IF amplifier contains the 32 dB amplifier stage
and has a gain of either 0 or 32 dB. The IF amplifier is
followed by a quadrature mixer with a fixed gain of
4 dB. The first baseband amplifier (G3, G2, G6) after
the low-pass filter and demodulator has gains
selectable between 0, 4, 8, 12, 16, 20, 24, and 28 dB.
Using the other gain steps, the IF and baseband gain
can be varied by 64 dB in 4 dB steps. The second
baseband amplifier (G5, G1) has gains selectable
between 0, 4, 21, and 25 dB. The 21 dB gain step in
the second baseband amplifier section is not tested
and should therefore not be used. Figure 3 is a
diagram of the gain steps.
6
16/0
8/0
4/0
21/0
G4
G3
G2
G6*
G1
G5*
LPF1
LPF2
*Not tested.
4/0
32/0
Figure 3. IF Amplifier Gain Steps
The baseband amplifier section contains dc correction
circuitry that minimizes dc offsets at the I/Q outputs.
The low-pass filters in the baseband contain a self-
calibrating circuit for tuning of filter cut-off frequency.
The selectable gain settings are programmed via the
TR register as described in the Programming
Information section. Filter tuning and dc calibration
are also explained in that section.
To achieve the specified absolute gain accuracy, the
total gain should be calibrated at room temperature.
This would normally be part of the overall phone
calibration. Absolute gain accuracy measures the gain
change over a specified temperature range relative to
the room temperature measurement. In the GSM
system, this specification is dependent on all the RX
functional blocks and not solely on the IF strip. The
relative gain accuracy is a measure of the gain stage
accuracy over a 20 dB range (see Figure 4). Relative
gain accuracy is determined after calibration of the
32 dB amplifier.
Note:
=
Y
,
X
relative gain accuracy.
Figure 4. Actual Gain vs. Requested Gain
The input impedance of the IF strip will vary slightly
when the 32 dB amplifier is switched between the ON
and OFF states. We recommend that the IF strip be
matched with the 32 dB amplifier in the ON state to
provide the best match to the SAW filter when the
input level is at a minimum. The input matching
network can match the IF input directly to the SAW
filter or to 50
.
A matching network to 50
was chosen for the
evaluation board to allow for convenient laboratory
measurements. To keep the input impedance low and
minimize impedance variation between gain settings
of the IF stage, a resistor is shunt-connected between
the input terminals. The input network can then be
matched to the desired input impedance. (The
specified gain includes a resistor value of 500
.) For
testing purposes, the input has been matched to 50
,
and the gains of the IF/baseband amplifier are all
referred to a 50
matched input impedance. The I/Q
outputs are terminated in high-impedance loads. The
gains are voltage gains and include the voltage gain in
the impedance transformation of the input matching
network. The network is illustrated in Figure 5.
32/0
R1
500
1:1
INPUT
IMPEDANCE
50
IFIN PIN 34
Note: Balun is shown for testing purposes only.
W3020 G4 bit
IFIP PIN 35
Figure 5. IF Strip Balanced Input Matching
Network
ACTUAL = REQUESTED
REQUESTED GAIN (dB)
ACTUAL
GAIN
(dB)
X
Y
ACTUAL GAIN
20 dB
相關PDF資料
PDF描述
W3030 W3030 3 V Dual-Mode IF Cellular Receiver
W3100A i2Chip W3100A
W312-02 FTG for VIA K7 Series Chipset with Programmable Output Frequency
W312-02H FTG for VIA K7 Series Chipset with Programmable Output Frequency
W312-02HT FTG for VIA K7 Series Chipset with Programmable Output Frequency
相關代理商/技術參數
參數描述
W3020A 制造商:Pulse 功能描述:BAR ANT LKCE 2.6 WIMAX
W3020-K 功能描述:天線 Wi-Max Ceramic Evaluation Kit RoHS:否 制造商:Molex 技術類型:Cellular Antenna 頻率: 帶寬: 尺寸:106.7 mm L x 13 mm W
W3022 功能描述:天線 DECT Ceramic Antenna RoHS:否 制造商:Molex 技術類型:Cellular Antenna 頻率: 帶寬: 尺寸:106.7 mm L x 13 mm W
W3024 功能描述:天線 Ceramic Antenna MediaFLO RoHS:否 制造商:Molex 技術類型:Cellular Antenna 頻率: 帶寬: 尺寸:106.7 mm L x 13 mm W
W30-24S1.5 制造商:INTRONICS 制造商全稱:INTRONICS 功能描述:DC/DC MODULES
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*