- 您現在的位置：買賣IC網 > PDF目錄363881 > W3020 GSM Multiband RF Transceiver PDF資料下載
參數資料
| 型號： | W3020 |
| 英文描述： | GSM Multiband RF Transceiver |
| 中文描述： | 手機多頻段射頻收發器 |
| 文件頁數： | 32/44頁 |
| 文件大小： | 409K |
| 代理商： | W3020 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁當前第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
Advance Data Sheet
December 1999
W3020 GSM Multiband RF Transceiver
32
Lucent Technologies Inc.
Programming Information
(continued
)
Filter Tune and dc Offset Correction Timing
(continued)
dc Offset Calibration
The dc offset calibration operation is controlled by several bits in the CONFIG and TR registers:
n
DS: dc correction skip, in the TR register
n
DP: dc precharge only, in the TR register
n
C5: dc correction disable, in the CONFIG register
n
C7: dc coarse/fine correction, in the CONFIG register
n
DT: dc correction time, in the CONFIG register
When the dc correction disable bit (C5) in the CONFIG register is written high, the dc offset correction circuitry
charges to a default value, corresponding to 0 dc offset, and any request for dc offset calibration is ignored. If dc
correction disable = 0, the dc offset calibration is initiated by writing the MO bits in the TR (or MAIN) register to a
value of 111 while dc correction skip (DS) and dc precharge only (DP) are both low. As in the case of the filter
tune, start of dc offset calibration is held off for about 15
μ
s while the bias circuits and input clock buffer start-up.
f the FTR bit was also written high coincident with entering RX mode, a filter tune is performed first, after which
dc offset calibration begins automatically.
The dc offset calibration runs for a time determined by the dc offset correction time bits DT[0:2] in the CONFIG
register. There are three of these bits, giving the user a choice of eight different correction times.
Upon completion of the dc offset calibration, the 3.25 MHz baseband clock stops and full receive mode is
entered automatically, with the LO1 buffer and LNA (if G0 = 1) being enabled automatically.
f RX mode is entered with dc precharge only (DP = 1) set high, dc offset circuitry runs through a much shorter
calibration routine, after which normal receive mode is entered automatically. The precharge-only operation
functions much the same as the normal calibration operation in that the LO1 buffer and LNA is disabled until
completion of the precharge operation. The 15
μ
s bias start-up time is still incurred.
The receive circuitry conditions during dc calibration are also controlled by two other bits in the CONFIG register:
n
C2: LNA on during dc calibration, when high
n
C3: receive LO1 buffer on during dc, calibration when high
For both the standard dc offset calibration cycle and the dc precharge-only operation, it is possible to perform dc
offset calibration with the LNA and/or LO1 buffer on by setting the C2 and C3 bits in the CONFIG register.
相關PDF資料 |
PDF描述 |
|---|---|
| W3030 | W3030 3 V Dual-Mode IF Cellular Receiver |
| W3100A | i2Chip W3100A |
| W312-02 | FTG for VIA K7 Series Chipset with Programmable Output Frequency |
| W312-02H | FTG for VIA K7 Series Chipset with Programmable Output Frequency |
| W312-02HT | FTG for VIA K7 Series Chipset with Programmable Output Frequency |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W3020A | 制造商:Pulse 功能描述:BAR ANT LKCE 2.6 WIMAX |
| W3020-K | 功能描述:天線 Wi-Max Ceramic Evaluation Kit RoHS:否 制造商:Molex 技術類型:Cellular Antenna 頻率: 帶寬: 尺寸:106.7 mm L x 13 mm W |
| W3022 | 功能描述:天線 DECT Ceramic Antenna RoHS:否 制造商:Molex 技術類型:Cellular Antenna 頻率: 帶寬: 尺寸:106.7 mm L x 13 mm W |
| W3024 | 功能描述:天線 Ceramic Antenna MediaFLO RoHS:否 制造商:Molex 技術類型:Cellular Antenna 頻率: 帶寬: 尺寸:106.7 mm L x 13 mm W |
| W30-24S1.5 | 制造商:INTRONICS 制造商全稱:INTRONICS 功能描述:DC/DC MODULES |
發布緊急采購，3分鐘左右您將得到回復。