- 您現在的位置：買賣IC網 > PDF目錄363901 > W79E803ADG (WINBOND ELECTRONICS CORP) 8-BIT MICROCONTROLLER PDF資料下載
參數資料
| 型號： | W79E803ADG |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT MICROCONTROLLER |
| 中文描述： | 8-BIT, FLASH, 20 MHz, MICROCONTROLLER, PDIP20 |
| 封裝： | 0.300 INCH, ROHS COMPLIANT, DIP-20 |
| 文件頁數： | 98/115頁 |
| 文件大小： | 1456K |
| 代理商： | W79E803ADG |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁當前第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁
W79E804A/803A/802A
- 98 -
Figure
24-2: I2C Timer Count Block Diagram
24.3 Modes of Operation
The on-chip I2C ports support five operation modes, Master transmitter, Master receiver, Slave
transmitter, Slave receiver, and GC call.
In a given application, I2C port may operate as a master or
as a slave. In the slave mode, the I2C port
hardware looks for its own slave address and the general call address. If one of these addresses is
detected, and if the slave is willing to receive or transmit data from/to master(by setting the AA bit),
acknowledge pulse will be transmitted out on the 9th clock, hence an interrupt is requested on both
master and slave devices if interrupt is enabled. When the microcontroller wishes to become the bus
master, the hardware waits until the bus is free before the master mode is entered so that a possible
slave action is not interrupted. If bus arbitration is lost in the master mode, I2C port switches to the
slave mode immediately and can detect its own slave address in the same serial transfer.
24.3.1 Master Transmitter Mode
Serial data output through SDA while SCL outputs the serial clock. The first byte transmitted contains
the slave address of the receiving device (7 bits) and the data direction bit. In this case the data
direction bit (R/W) will be logic 0, and it is represented by “W” in the flow diagrams. Thus the first byte
transmitted is SLA+W. Serial data is transmitted 8 bits at a time. After each byte is transmitted, an
acknowledge bit is received. START and STOP conditions are output to indicate the beginning and the
end of a serial transfer.
24.3.2 Master Receiver Mode
In this case the data direction bit (R/W) will be logic 1, and it is represented by “R” in the flow
diagrams. Thus the first byte transmitted is SLA+R. Serial data is received via SDA while SCL outputs
the serial clock. Serial data is received 8 bits at a time. After each byte is received, an acknowledge bit
is transmitted. START and STOP conditions are output to indicate the beginning and end of a serial
transfer.
相關PDF資料 |
PDF描述 |
|---|---|
| W79E803ASG | 8-BIT MICROCONTROLLER |
| W79E804 | 8-BIT MICROCONTROLLER |
| W79E804A | 8-BIT MICROCONTROLLER |
| W79E804ADG | 8-BIT MICROCONTROLLER |
| W79E804ASG | 8-BIT MICROCONTROLLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W79E803ASG | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-BIT MICROCONTROLLER |
| W79E804 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-BIT MICROCONTROLLER |
| W79E804A | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-BIT MICROCONTROLLER |
| W79E804ADG | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-BIT MICROCONTROLLER |
| W79E804ASG | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-BIT MICROCONTROLLER |
發布緊急采購，3分鐘左右您將得到回復。