- 您現在的位置：買賣IC網 > PDF目錄363903 > W86L488 (WINBOND ELECTRONICS CORP) SD/ SDIO/ MMC MEMORY CARD BRIDGE PDF資料下載
參數資料
| 型號： | W86L488 |
| 廠商： | WINBOND ELECTRONICS CORP |
| 英文描述： | SD/ SDIO/ MMC MEMORY CARD BRIDGE |
| 中文描述： | SD / SDIO記憶/ MMC記憶卡橋 |
| 文件頁數： | 27/45頁 |
| 文件大?。?/td> | 1842K |
| 代理商： | W86L488 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁
Preliminary W86L488
A[3:1]
D[15:0]
XCSN
XRDN
System_
Clock
011
XWRHN
0x90XX
011
1xx0xxxxb
Publication Release Date: February 5, 2004
- 24 -
Revision 0.82
Fig. 7-10 Timing of Interrupt in (XINTN pin goes to low again).
XINTN
7.2 Card Inserting and Removing
There are two method for Host to detect SD/SDIO or MMC card inserting or removing through
W86L488, the first method is detected by CD/DAT3 pin, the second method is a dedicate switch on
the SD/MMC slot can be connected to the GIO0 pin and set GIO0 to input direction. These two
methods can be performed even if the W86L488 is in power down state.
Method 1, CD/DAT3 as card detection:
The CD/DAT3 of SD bus can be used as card detection if no data transfer on the DAT3, if SIEN bit of
the control register is low and CD_IE and INT_E on the interrupt enable register are all high, card
inserting or removing will generate interrupt. Host must read the interrupt status register and re-check
the card state by read the CD bit on the extend status register. This detection method will not effective
when wide bus on the SD bus is transfer. MMC card may not support this detection method.
Method 2, GIO0, GIP6 as card detection (inserting):
Some SD/MMC slot support external switch for card existing detection, the switch will on when
SD/SDIO or MMC card is exist. GIO0 and GIP6 with a pull high resister can be used as card detection
of port A and port B. In port A the Host can disable the GOEN0 bit on the general I/O port control
register and enable the GIT_EN0 bit on the general I/O port interrupt enable register and enable
GIT_IE and INT_E bits on the interrupt enable register. SD or MMC card inserting or removing will
change the switch state then change the state of GIO0 pin and then generate interrupt to the Host.
Host may re-check the card state by read the GIN0 bit on the general I/O port data register. The card
insert status of port A and port B also can be read in the global status and control register.
Figure 7-10 shows the waveform of GIO0 and GIOx when card insert and remove if GIO0 as card
insert and GIOx as write protect input.
相關PDF資料 |
PDF描述 |
|---|---|
| W86L488AY | SD/ SDIO/ MMC MEMORY CARD BRIDGE |
| W86L488Y | SD/ SDIO/ MMC MEMORY CARD BRIDGE |
| W88111AF | ATAPI CD-ROM DECODER & CONTROLLER |
| W88112F | ATAPI CD-ROM DECODER & CONTROLLER |
| W88113C | ATAPI CD-ROM DECODER & CONTROLLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W86L488AY | 制造商:WINBOND 制造商全稱:Winbond 功能描述:SD/ SDIO/ MMC MEMORY CARD BRIDGE |
| W86L488AY-SA5772001CA-REV C | 制造商:Nuvoton Technology Corp 功能描述:IC FLASH MEM CARD BRIDGE |
| W86L488AY-SA5772001DA-REV D | 制造商:Nuvoton Technology Corp 功能描述:IC FLASH MEM CARD BRIDGE |
| W86L488Y | 制造商:WINBOND 制造商全稱:Winbond 功能描述:SD/ SDIO/ MMC MEMORY CARD BRIDGE |
| W86L488Y-SA5772001CA-REV C | 制造商:Nuvoton Technology Corp 功能描述:IC FLASH MEM CARD BRIDGE |
發布緊急采購，3分鐘左右您將得到回復。