国产精品成人VA在线观看-国产乱妇乱子视频在播放-国产日韩精品一区二区三区在线-国模精品一区二区三区

參數資料
型號： W89C926
廠商： WINBOND ELECTRONICS CORP
英文描述： PCMCIA ETHERNET NETWORK TWISTED PAIR INTERFACE CONTROLLER
中文描述： PCMCIA以太網雙絞線網絡接口控制器
文件頁數： 23/48頁
文件大小： 395K
代理商： W89C926
W89C926 PENTIC+
Publication Release Date: January 1996
- 23 -
Revision A1
out before the buffer ring overflows. This is done through a remote DMA read operation, which is
simply a "IN" command on the PC.
SHARED MEMORY MODE OPERATION
In this mode, the local memory is mapped as part of the system memory. When it requires data
transmission, the host fills the transmit buffer SRAM by a memory move operation and then issues a
transmit command to the PENTIC+. When it receives data, the PENTIC+ will generate an interrupt
to the host by asserting IREQ when one or more packets have been received. The PENTIC+ will then
place the packets into the shared memory. The host should check the shared memory and remove
the data before the buffer ring overflows.
Bus arbitration is performed between the host and LCE core for shared memory usage. When
memory accesses are issued, the arbiter will grant the bus master an acknowledge signal, which is a
BACK to the LCE or a WAIT signal to the host. There is no predefined priority in the PENTIC+; bus
arbitration is performed on a first-come, first-served basis.
To implement the shared memory mode, the PENTIC+ uses memory mapping register A (MMA) and
memory mapping register B (MMB) for memory mapping control. Since the PENTIC+ will operate in
16-bit shared memory operation at shared memory base address 00000H only, 0s should be written
to MMB and bit 0 to 5 of MMA. The contents of the MMA are described below.
MMA (Memory Mapping Register A)
MMA is used for memory enable and software reset. It is located in I/O space, 00H, and can be ac-
cessed only in shared memory mode.
Access Address: IOBASE + 00H
Access Type: write-only
BIT
SYMBOL
0-5
-
Reserved. Should be set to 0.
6
MEN
If this bit is high, the buffer memory may be accessed by the
system; if it is low, the buffer memory access is disabled. This
bit is 0 at power-on.
7
SRESET
A shared memory mode software reset is issued when a 1 is
written to this bit. Writing a 0 to this bit will clear the software
reset. This bit is 0 at power-on.
DESCRIPTION
AUTO MEDIA-SWITCHING FUNCTION
The PENTIC+ also provides a user-friendly auto media-switching function. If the PENTIC+ is
configured at the TPI, link checking is enabled, and the UTP link is broken, the PENTIC+ will detect
the link status and switch to the BNC port immediately. After the UTP link is repaired, the PENTIC+
will detect the good link and switch back to the TPI again.
If, however, the PENTIC+ is not configured at the TPI or link checking is disabled, the auto media-
switching function will be disabled.
相關PDF資料
PDF描述
W89C926F 10M PCMCIA Ethernet Network Interface Controller
W89C940 ELANC-PCI (TWISTED-PAIR ETHER-LAN CONTROLLER WITH PCI INTERFACE)
W89C982 INTEGRATED MULTIPLE REPEATER II
W89C982AF INTEGRATED MULTIPLE REPEATER II
W8NB80 N - CHANNEL 800V - 1.2ohm - 7.5A - TO-247 PowerMESH MOSFET
相關代理商/技術參數
參數描述
W89C926F 制造商:WINBOND 制造商全稱:Winbond 功能描述:10M PCMCIA Ethernet Network Interface Controller
W89C926PENTIC+ 制造商:WINBOND 制造商全稱:Winbond 功能描述:PCMCIA ETHERNET NETWORK TWISTED PAIR INTERFACE CONTROLLER
W89C92P 制造商:未知廠家 制造商全稱:未知廠家 功能描述:10M CMOS Coaxial Transceiver
W89C940 制造商:WINBOND 制造商全稱:Winbond 功能描述:ELANC-PCI (TWISTED-PAIR ETHER-LAN CONTROLLER WITH PCI INTERFACE)
W89C940F 制造商:未知廠家 制造商全稱:未知廠家 功能描述:10M PCI-Bus Ethernet Network Interface Controller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*