- 您現在的位置：買賣IC網 > PDF目錄363904 > W89C926F (WINBOND ELECTRONICS CORP) 10M PCMCIA Ethernet Network Interface Controller PDF資料下載
參數資料
| 型號： | W89C926F |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 10M PCMCIA Ethernet Network Interface Controller |
| 中文描述： | 2 CHANNEL(S), LOCAL AREA NETWORK CONTROLLER, PQFP100 |
| 封裝： | TQFP-100 |
| 文件頁數： | 15/48頁 |
| 文件大小： | 395K |
| 代理商： | W89C926F |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
W89C926 PENTIC+
Publication Release Date: January 1996
- 15 -
Revision A1
CCSR (Card Configuration and Status Register)
Access Address: AMBase + 00FD2H
Access Type: Attribute Memory Read/Write
BIT
0
1
SYMBOL
-
Intr
DESCRIPTION
Reserved, must be 0.
Interrupt Status
This bit indicates the internal status of an interrupt request. It remains high
until the condition that caused the interrupt request has been serviced.
This bit is 0 at power-on.
Reserved, must be 0s.
2-7
-
SCR (Socket and Copy Register)
The SCR is used to enable the PENTIC+ to distinguish between similar cards installed in the same
system.
Access Address: AMBase + 00FD6H
Access Type: Attribute Memory Read/Write
BIT
SYMBOL
DESCRIPTION
0-3
SocNum
Socket Number
Set these bits to indicate to the PENTIC+ that it is located in the n'th
socket. The first socket is numbered 0. This permits any cards designed to
do so to share a common set of IO ports while remaining uniquely
identifiable. These bits are 0 at power-on.
4-6
CopNum
Copy Number
Set these bits to indicate to the PENTIC+ that it is the n'th copy of another
card installed in the system that is configured identically. The first identical
card should be assigned a value of 0 as its copy number. This permits any
cards designed to do so to share a common set of I/O ports while
remaining uniquely identifiable and consecutively ordered. These bits are
0s at power-on.
7
-
Reserved, must be 0.
LAN Configuration Register Set
These two registers are used for LAN configuration control.
CFA (Configuration Register A)
This register is used to select the PENTIC+'s operating mode and LED control.
Access Address: AMBase + 00FF0H
Access Type: Attribute Memory Read/Write
相關PDF資料 |
PDF描述 |
|---|---|
| W89C940 | ELANC-PCI (TWISTED-PAIR ETHER-LAN CONTROLLER WITH PCI INTERFACE) |
| W89C982 | INTEGRATED MULTIPLE REPEATER II |
| W89C982AF | INTEGRATED MULTIPLE REPEATER II |
| W8NB80 | N - CHANNEL 800V - 1.2ohm - 7.5A - TO-247 PowerMESH MOSFET |
| W90100F | Embedded Micro-Controller(32位嵌入式的微控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W89C926PENTIC+ | 制造商:WINBOND 制造商全稱:Winbond 功能描述:PCMCIA ETHERNET NETWORK TWISTED PAIR INTERFACE CONTROLLER |
| W89C92P | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:10M CMOS Coaxial Transceiver |
| W89C940 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:ELANC-PCI (TWISTED-PAIR ETHER-LAN CONTROLLER WITH PCI INTERFACE) |
| W89C940F | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:10M PCI-Bus Ethernet Network Interface Controller |
| W89C982 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:INTEGRATED MULTIPLE REPEATER II |
發布緊急采購，3分鐘左右您將得到回復。