- 您現在的位置：買賣IC網 > PDF目錄363908 > W921C400 (WINBOND ELECTRONICS CORP) 4-Bit Microcontroller(4位的微控制器) PDF資料下載
參數資料
| 型號： | W921C400 |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 4-Bit Microcontroller(4位的微控制器) |
| 中文描述： | 4-BIT, MROM, 4 MHz, MICROCONTROLLER, PDIP28 |
| 封裝： | DIP-28 |
| 文件頁數： | 13/53頁 |
| 文件大小： | 399K |
| 代理商： | W921C400 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁
W921E400A/W921C400
Publication Release Date: July 1999
- 13 -
Revision A3
The W921E400A/W921C400 provides a crystal or RC oscillation circuit selected by bit0 of INI
register (refer to section 6.14) to generate the system clock through external connections. If a crystal
oscillator is used, a crystal or ceramic resonator must be connected to OSCI and OSCO, and the
capacitor must be connected if an accurate frequency is needed. The oscillator configuration is shown
as follows.
OSCI
OSCO
or
OSCI
OSCO
RC type
Crystal Type
6.4 Initial State
The W921E400A/W921C400 is reset either by a power-on reset or by using the external RESET pin.
The initial state of the W921E400A/W921C400 after the reset function is executed is described
below. The EVF interrupt request signal register value is random, so user must do CLR
EVF,#11111111b instruction to clear all interrupt request signals after power-on reset.
Program counter (PC)
Stack pointer
Special function registers
TM0, TM2, TM3 input clock
TM0, TM2, TM3 contents
I/O port
PM registers
DTMF output
EVF interrupt request signal register
0000H
0FFH
Refer to section 6.2.1
Fosc / 8
0FFH
Input mode
1111B
Disable (H-Z)
Random
6.5 Input/Output
There are 21 I/O pins. All the I/O pins will remain in the input mode after power on reset.
The I/O instructions are described as follows:
MOV
MOV
MOV
MOV
A, Px
B, Px
Px, A
Px, B
Input port x to A accumulator
Input port x to B accumulator
Output A accumulator data to port x.
Output B accumulator data to port x.
The input or output status of port 2 to port 6 can be pin controlled by port mode register (PMx, where
x = 2 to 6). Data 0 in PMx indicates the corresponding pin as output mode, and data 1 indicates the
relative pin as input mode. For example, MOV PM3, #0101B, it sets P3.0 and P3.2 in input mode and
P3.1 and P3.3 in output mode. The I/O instructions don't affect the input or output mode in port2 to
port6.
相關PDF資料 |
PDF描述 |
|---|---|
| W921C840 | 4-Bit Microcontroller(4位微控制器) |
| W921E840A | 4-Bit Microcontroller(4位微控制器) |
| W921E843A | 4-BIT MICROCONTROLLER |
| W921C880 | 4-Bit Microcontroller(4位微控制器) |
| W921E880A | 4-Bit Microcontroller(4位微控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W921C840 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| W921C880 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| W921E400 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:4-BIT MICROCONTROLLER |
| W921E400A | 制造商:WINBOND 制造商全稱:Winbond 功能描述:4-BIT MICROCONTROLLER |
| W921E840 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:4-BIT MICROCONTROLLER |
發布緊急采購，3分鐘左右您將得到回復。