- 您現在的位置：買賣IC網 > PDF目錄363908 > W921C400 (WINBOND ELECTRONICS CORP) 4-Bit Microcontroller(4位的微控制器) PDF資料下載
參數資料
| 型號： | W921C400 |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 4-Bit Microcontroller(4位的微控制器) |
| 中文描述： | 4-BIT, MROM, 4 MHz, MICROCONTROLLER, PDIP28 |
| 封裝： | DIP-28 |
| 文件頁數： | 25/53頁 |
| 文件大?。?/td> | 399K |
| 代理商： | W921C400 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁
W921E400A/W921C400
Publication Release Date: July 1999
- 25 -
Revision A3
The format of the TM0 control register (TM0CR) is described below:
TM0CR register: (address = 020H, default data = 0H)
b3
b2
b1
b0
b1
b0
Input frequency (f )
0
0
0
1
1
0
1
1
fsys/2 Hz
fsys/256 Hz
fsys/1024 Hz
fsys/2048 Hz
Reserved
Reserved
The TM0 set register is divided into TM0 MSB data register (TM0MSB register, address = 021H,
default = 0FH) and TM0 LSB data register (TM0LSB register, address = 022H, default = 0FH).
TM0 will underflow when TM0 set register is from 00H to 0FFH and the value in the TM0MSB and
TM0LSB will be auto reloaded to the TM0 set register when the STTM0 bit2 is set. TM0 will decrease
by 1 at the frequency of timer 0 clock after the timer 0 has started.
If at any time the STTM0 bit3 is from 0 to 1 (disable to enable) in the timer mode, the TM0MSB and
TM0LSB will be auto reloaded to the TM0 set register again and restart the timer 0. TM0 will stop
operating while the STTM0 bit3 is reset to 0.
The TM0 starts to count when the STTM0 register bit3 is set. When TM0 underflows, the STTM0 bit3
will be reset by hardware to stop TM0 if the auto-reload is disabled, but the STTM0 bit3 will not be
reset if the auto-reload is enabled.
When the TM0 normal function is performed, the watch-dog timer function will be disabled
automatically.
The format of the TM0 status register (STTM0) is described below:
STTM0 register: (address = 023H, default data = 0H)
b3
b2
b1
b0
0:TM0 stop
1:TM0 start
0:TM0 normal function selected
1:Watch-dog timer (WDT) selected
0:WDT not underflow
1:WDT underflow
0:TM0 auto-reload disable
1:TM0 auto-reload enable
If TM0 works as the watch-dog timer (WDT), the bit1 of the STTM0 register will be set when the WDT
is underflow, in the meanwhile, the system is reset just as with the power on reset except the STTM0
bit1. The WDT (STTM0 bit1) will be reset to zero only with power on reset or RAM write mode.
In the timer mode the time out will be the programming data subtract 1 ([TM0MSB, TM0LSB]-1). TM2
and TM3 are the same as TM0.
相關PDF資料 |
PDF描述 |
|---|---|
| W921C840 | 4-Bit Microcontroller(4位微控制器) |
| W921E840A | 4-Bit Microcontroller(4位微控制器) |
| W921E843A | 4-BIT MICROCONTROLLER |
| W921C880 | 4-Bit Microcontroller(4位微控制器) |
| W921E880A | 4-Bit Microcontroller(4位微控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W921C840 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| W921C880 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| W921E400 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:4-BIT MICROCONTROLLER |
| W921E400A | 制造商:WINBOND 制造商全稱:Winbond 功能描述:4-BIT MICROCONTROLLER |
| W921E840 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:4-BIT MICROCONTROLLER |
發布緊急采購，3分鐘左右您將得到回復。