国产精品成人VA在线观看-国产乱妇乱子视频在播放-国产日韩精品一区二区三区在线-国模精品一区二区三区

參數資料
型號: AD8325-EVAL
廠商: Analog Devices, Inc.
英文描述: 5 V CATV Line Driver Fine Step Output Power Control
中文描述: 5伏精細有線電視線路驅動器輸出功率控制步
文件頁數: 9/16頁
文件大小: 304K
代理商: AD8325-EVAL
REV. 0
AD8325
–9–
Distortion, Adjacent Channel Power, and DOCSIS
In order to deliver 58 dBmV of high fidelity output power required
by DOCSIS, the PA should be able to deliver about 61 dBmV
in order to make up for losses associated with the transformer
and diplexer. TPC 7 and TPC 8 show the AD8325 second and
third harmonic distortion performance versus fundamental
frequency for various output power levels. These figures are
useful for determining the inband harmonic levels from 5 MHz
to 65 MHz. Harmonics higher in frequency will be sharply attenu-
ated by the low-pass filter function of the diplexer. Another
measure of signal integrity is adjacent channel power or ACP.
DOCSIS section 4.2.9.1.1 states,
Spurious emissions from
a transmitted carrier may occur in an adjacent channel that could
be occupied by a carrier of the same or different symbol rates.
TPC 12 shows the measured ACP for a 16 QAM, 61dBmV signal,
taken at the output of the AD8325 evaluation board (see Figure
12 for evaluation board schematic). The transmit channel width
and adjacent channel width in TPC 12 correspond to symbol rates
of 160 K
SYM/SEC
. Table I shows the ACP results for the AD8325
for all conditions in DOCSIS Table 4-7
Adjacent Channel
Spurious Emissions.
Noise and DOCSIS
At minimum gain, the AD8325
s output noise spectral density is
10 nV/
Hz
measured at 10 MHz. DOCSIS Table 4-8,
Spurious
Emissions in 5 MHz to 42 MHz,
specifies the output noise for
various symbol rates. The calculated noise power in dBmV for
160 K
SYM/SECOND
is:
20
10
160
60
48
2
log
nV
Hz
kHz
dBmV
×
+
=
Comparing the computed noise power of
48 dBmV to the
8 dBmV signal yields
56 dBc, which meets the required level of
53 dBc set forth in DOCSIS Table 4-8. As the AD8325
s gain is
increased from this minimum value, the output signal increases at a
faster rate than the noise, resulting in a signal to noise ratio that
improves with gain. In transmit disable mode, the output noise
spectral density computed over 160 K
SYM/SECOND
is 1.0 nV/
Hz
or
68 dBmV.
Evaluation Board Features and Operation
The AD8325 evaluation board (Part # AD8325-EVAL) and
control software can be used to control the AD8325 upstream
cable driver via the parallel port of a PC. A standard printer
cable connected between the parallel port and the evaluation
board is used to feed all the necessary data to the AD8325 by
means of the Windows-based, Microsoft Visual Basic control
software. This package provides a means of evaluating the
amplifier by providing a convenient way to program the gain/
attenuation as well as offering easy control of the amplifiers
asynchronous TXEN and
SLEEP
pins. With this evaluation kit
the AD8325 can be evaluated with either a single-ended or differ-
ential input configuration. The amplifier can also be evaluated
with or without the PULSE diplexer in the output signal path. To
remove the diplexer from the signal path, leave R6 and R8 open
and install a 0
chip resistor at R7. A schematic of the evalua-
tion board is provided in Figure 12.
Overshoot on PC Printer Ports
The data lines on some PC parallel printer ports have excessive
overshoot that may cause communications problems when pre-
sented to the CLK pin of the AD8325 (TP6 on the evaluation
board). The evaluation board was designed to accommodate a
series resistor and shunt capacitor (R2 and C5) to filter the
CLK signal if required.
Transformer and Diplexer
A 1:1 transformer is needed to couple the differential outputs of
the AD8325 to the cable while maintaining a proper impedance
match. The specified transformer is available from TOKO (Part
# 617DB-A0070); however, MA/COM part # ETC-1-1T-15
can also be used. The evaluation board is equipped with the
TOKO transformer, but is also designed to accept the MA/COM
transformer. The PULSE diplexer included on the evaluation
board provides a high-order low-pass filter function, typically
used in the upstream path. The ability of the PULSE diplexer
to achieve DOCSIS compliance is neither expressed nor implied
by Analog Devices Inc. Data on the diplexer can be obtained
from PULSE.
Table I. ACP Performance for All DOCSIS Conditions (All Values in dBc)
160 K
SYM/SEC
320 K
SYM/SEC
640 K
SYM/SEC
1280 K
SYM/SEC
2560 K
SYM/SEC
ADJACENT CHANNEL SYMBOL RATE
TRANSMIT
CHANNEL
SYMBOL
RATE
66.7
67.6
62.0
56.3
54.1
53.8
55.6
61.1
67.0
53.1
53.8
56.0
61.5
54.3
53.2
54.0
56.3
56.3
54.3
53.4
54.1
58.5
56.2
54.4
53.5
160 K
SYM/SEC
320 K
SYM/SEC
640 K
SYM/SEC
1280 K
SYM/SEC
2560 K
SYM/SEC
相關PDF資料
PDF描述
AD8325 Fast Switching Digitally Controlled Variable Gain Amplifier(快速轉換數字控制的可變增益放大器)
AD8326ARE-EVAL ER 4C 4#0 PIN RECP
AD8326ARE-REEL High Output Power Programmable CATV Line Driver
AD8326ARP-EVAL High Output Power Programmable CATV Line Driver
AD8326ARP-REEL High Output Power Programmable CATV Line Driver
相關代理商/技術參數
參數描述
AD8326 制造商:AD 制造商全稱:Analog Devices 功能描述:High Output Power Programmable CATV Line Driver
AD8326ARE 制造商:Analog Devices 功能描述:SP Amp Line Driver Amp Single 制造商:Rochester Electronics LLC 功能描述:TSSOP HIGH OUTPUT POWER CATV LINE DRIVER - Bulk
AD8326ARE-EVAL 制造商:Analog Devices 功能描述:Evaluation Board For AD8326 High Output Power Programmable CATV Line Driver
AD8326ARE-REEL 制造商:Analog Devices 功能描述:SP Amp Line Driver Amp Single 制造商:Analog Devices 功能描述:SP Amp Line Driver Amp Single ±5.25V/12.6V 28-Pin TSSOP EP T/R 制造商:Rochester Electronics LLC 功能描述:TSSOP HIGH OUTPUT POWER CATV LINE DRIVER - Tape and Reel
AD8326AREZ 功能描述:IC LINE DVR CATV PROG 28TSSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 視頻處理 系列:- 產品變化通告:Product Discontinuation 07/Mar/2011 標準包裝:3,000 系列:OMNITUNE™ 類型:調諧器 應用:移動電話,手機,視頻顯示器 安裝類型:表面貼裝 封裝/外殼:65-WFBGA 供應商設備封裝:PG-WFSGA-65 包裝:帶卷 (TR) 其它名稱:SP000365064