- 您現在的位置：買賣IC網 > PDF目錄363894 > W741C260 (WINBOND ELECTRONICS CORP) 4-BIT Microcontroller(多次可編程4位的微控制器) PDF資料下載
參數資料
| 型號： | W741C260 |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 4-BIT Microcontroller(多次可編程4位的微控制器) |
| 中文描述： | 4-BIT, MROM, 4.19 MHz, MICROCONTROLLER, PQFP80 |
| 封裝： | QFP-80 |
| 文件頁數： | 16/92頁 |
| 文件大小： | 488K |
| 代理商： | W741C260 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁
W741C260
- 16 -
INT must be executed again. Otherwise, these interrupts can be disabled by executing DIS INT
instruction. The bit descriptions are as follows:
w
1
2
3
IEF
4
w
w
5
6
0
w
w
7
Note: W means write only.
IEF.0 = 1 Interrupt 0 is accepted by overflow from the Divider 0.
IEF.1 = 1 Interrupt 1 is accepted by underflow from the Timer 0.
IEF.2 = 1 Interrupt 2 is accepted by a signal change on port RC.
IEF.3 Reserved
IEF.4 = 1 Interrupt 0 is accepted by overflow from the Divider 1.
IEF.5 & IEF.6 are reserved.
IEF.7 = 1 Interrupt 7 is accepted by underflow from Timer 1.
Stop Mode Operation
In stop mode, all operations of the
μ
C cease (excluding the operation of sub-oscillator and divider 1
when the dual-clock operation mode is selected). The
μ
C enters stop mode when the STOP
instruction is executed and exits stop mode when an external trigger is activated (by a falling signal
on the RC port). When the designated signal is accepted, the
μ
C awakens and executes the next
instruction (if the corresponding bits of IEF and PEF have been set, It will enter the interrupt service
routine after stop mode released). To prevent erroneous execution, the NOP instruction should follow
the STOP command.
Stop Mode Wake-up Enable Flag for Port RC (SEF)
The stop mode wake-up flag for port RC is organized as a 4-bit binary register (SEF.0 to SEF.3).
Before port RC may be used to make the device exit the stop mode, the content of the SEF must be
set first. The SEF is controlled by the MOV SEF, #I instruction. The bit descriptions are as follows:
0
1
2
SEF
w
w
w
w
3
Note: W means write only.
SEF 0 = 1 Device will exit stop mode when falling edge signal is applied to pin RC.0.
SEF 1 = 1 Device will exit stop mode when falling edge signal is applied to pin RC.1.
SEF 2 = 1 Device will exit stop mode when falling edge signal is applied to pin RC.2.
SEF 3 = 1 Device will exit stop mode when falling edge signal is applied to pin RC.3.
相關PDF資料 |
PDF描述 |
|---|---|
| W741E20X | 4-BIT FLASH MICROCONTROLLER |
| W741E260 | 4-BIT FLASH MICROCONTROLLER |
| W741L260 | 4-BIT MICROCONTROLLER |
| W742C810 | 4-BIT MICROCONTROLLER |
| W742C813 | 4-BIT SINGLE-CHIP MICROCONTROLLER FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROL TRANSMITTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W741E200 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:4-Bit Microcontroller |
| W741E201 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:4-BIT FLASH MICROCONTROLLER |
| W741E202 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:4-BIT FLASH MICROCONTROLLER |
| W741E203 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:4-BIT FLASH MICROCONTROLLER |
| W741E204 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:4-BIT FLASH MICROCONTROLLER |
發布緊急采購，3分鐘左右您將得到回復。