- 您現在的位置：買賣IC網 > PDF目錄363894 > W741C260 (WINBOND ELECTRONICS CORP) 4-BIT Microcontroller(多次可編程4位的微控制器) PDF資料下載
參數資料
| 型號： | W741C260 |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 4-BIT Microcontroller(多次可編程4位的微控制器) |
| 中文描述： | 4-BIT, MROM, 4.19 MHz, MICROCONTROLLER, PQFP80 |
| 封裝： | QFP-80 |
| 文件頁數： | 18/92頁 |
| 文件大小： | 488K |
| 代理商： | W741C260 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁
W741C260
- 18 -
Hold Mode Release Enable Flag (HEF)
The hold mode release enable flag is organized as an 8-bit binary register (HEF.0 to HEF.7). The
HEF is used to control the hold mode release conditions. It is controlled by the MOV HEF, #I
instruction. The bit descriptions are as follows:
w
0
1
2
HEF
w
w
w
w
3
4
5
6
7
Note: W means write only.
HEF.0 = 1 Overflow from the Divider 0 causes hold mode to be released.
HEF.1 = 1 Underflow from Timer 0 causes hold mode to be released.
HEF.2 = 1 Signal change on port RC causes hold mode to be released.
HEF.3 Reserved
HEF.4 = 1 Overflow from the Divider 1 causes hold mode to be released.
HEF.5 & HEF.6 are reserved.
HEF.7 = 1 Underflow from Timer 1 causes hold mode to be released.
Port Enable Flag (PEF)
The port enable flag is organized as 4-bit binary register (PEF.0 to PEF.3). Before port RC may be
used to release the hold mode or preform interrupt function, the content of the PEF must be set first.
The PEF is controlled by the MOV PEF, #I instruction. The bit descriptions are as follows:
PEF
w
w
w
0
1
2
w
3
Note: W means write only.
PEF.0: Enable/disable the signal change on pin RC.0 to release hold mode or perform interrupt.
PEF.1: Enable/disable the signal change on pin RC.1 to release hold mode or perform interrupt.
PEF.2: Enable/disable the signal change on pin RC.2 to release hold mode or perform interrupt.
PEF.3: Enable/disable the signal change on pin RC.3 to release hold mode or perform interrupt.
Hold Mode Release Condition Flag (HCF)
The hold mode release condition flag is organized as a 8-bit binary register (HCF0 to HCF7). It
indicates by which interrupt source the hold mode has been released, and is loaded by hardware. The
HCF can be read out by the MOVA R, HCFL
and MOVA R, HCFH instructions. When any of the HCF
bits is "1," the hold mode will be released and the HOLD instruction is invalid. The HCF can be reset
by the CLR EVF,#I (EVF.n = 0) or MOV HEF,#I (HEF.n = 0) instructions. When EVF or HEF have
been reset, the corresponding bit of HCF is reset simultaneously. The bit descriptions are as follows:
R
R
HCF
0
1
2
3
4
5
R
R
R
6
7
Note: R means read only.
相關PDF資料 |
PDF描述 |
|---|---|
| W741E20X | 4-BIT FLASH MICROCONTROLLER |
| W741E260 | 4-BIT FLASH MICROCONTROLLER |
| W741L260 | 4-BIT MICROCONTROLLER |
| W742C810 | 4-BIT MICROCONTROLLER |
| W742C813 | 4-BIT SINGLE-CHIP MICROCONTROLLER FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROL TRANSMITTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W741E200 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:4-Bit Microcontroller |
| W741E201 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:4-BIT FLASH MICROCONTROLLER |
| W741E202 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:4-BIT FLASH MICROCONTROLLER |
| W741E203 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:4-BIT FLASH MICROCONTROLLER |
| W741E204 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:4-BIT FLASH MICROCONTROLLER |
發布緊急采購，3分鐘左右您將得到回復。