- 您現在的位置：買賣IC網 > PDF目錄363901 > W79E804 (WINBOND ELECTRONICS CORP) 8-BIT MICROCONTROLLER PDF資料下載
參數資料
| 型號： | W79E804 |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | 8位微控制器 |
| 英文描述： | 8-BIT MICROCONTROLLER |
| 中文描述： | 8位微控制器 |
| 文件頁數： | 95/115頁 |
| 文件大小： | 1456K |
| 代理商： | W79E804 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁當前第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁
W79E804A/803A/802A
Publication Release Date: July 16, 2007
- 95 -
Revision A2
24. I2C SERIAL CONTROL
The I2C bus uses two wires (SDA and SCL) to transfer information between devices connected to the
bus. The main features of the bus are:
– Bidirectional data transfer between masters and slaves
– Multimaster bus (no central master)
– Arbitration between simultaneously transmitting masters without corruption of serial data on the bus
– Serial clock synchronization allows devices with different bit rates to communicate via one serial bus
– Serial clock synchronization can be used as a handshake mechanism to suspend and resume serial
transfer
–
The I2C bus may be used for test and diagnostic purposes
–
t
BUF
STOP
SDA
SCL
START
t
HD;STA
t
LOW
t
HD;DAT
t
HIGH
t
f
t
SU;DAT
Repeated
START
t
SU;STA
t
SU;STO
STOP
t
r
Figure
24-1: I2C Bus Timing
The device’s on-chip I2C logic provides the serial interface that meets the I2C bus standard mode
specification. The I2C logic handles bytes transfer autonomously. It also keeps track of serial
transfers, and a status register (I2STATUS) reflects the status of the I2C bus.
The I2C port, SCL and SDA are at P1.2 and P1.3. When the I/O pins are used as I2C port, user must
set the pins to logic high in advance. When I2C port is enabled by setting ENS to high, the internal
states will be controlled by I2CON and I2C logic hardware. Once a new status code is generated and
stored in I2STATUS, the I2C interrupt flag (SI) will be set automatically. If both EA and EI2C are also
in logic high, the I2C interrupt is requested. The 5 most significant bits of I2STATUS stores the internal
state code, the lowest 3 bits are always zero and the content keeps stable until SI is cleared by
software.
24.1 SIO Port
The SIO port is a serial I/O port, which supports all transfer modes from and to the I2C bus. The SIO
port handles byte transfers autonomously. To enable this port, the bit ENS1 in I2CON should be set to
'1'. The CPU interfaces to the SIO port through the following six special function registers:
I2CON
(control register, C0H),
I2STATUS
(status register, BDH),
I2DAT
(data register, BCH),
I2ADDR
(address registers, C1H),
I2CLK
(clock rate register BEH) and
I2TIMER
(Timer counter register, BFH).
The SIO H/W interfaces to the I2C bus via two pins: SDA (P1.3, serial data line) and SCL (P1.2, serial
clock line). Pull up resistors are needed for Pin P1.2 and P1.3 for I2C operation as these are open
drain pins.
相關PDF資料 |
PDF描述 |
|---|---|
| W79E804A | 8-BIT MICROCONTROLLER |
| W79E804ADG | 8-BIT MICROCONTROLLER |
| W79E804ASG | 8-BIT MICROCONTROLLER |
| W80NF06 | N-CHANNEL 60V - 0.0065OHM - 80A TO-220/D2PAK/TO-247 STripFET II POWER MOSFET |
| W81181AD | USB HUB CONTROLLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W79E804A | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-BIT MICROCONTROLLER |
| W79E804ADG | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-BIT MICROCONTROLLER |
| W79E804ASG | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-BIT MICROCONTROLLER |
| W79E8213 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:W79E8213中文資料 |
| W79E8213_W79E8213R | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Table of contents- |
發布緊急采購，3分鐘左右您將得到回復。