- 您現在的位置：買賣IC網 > PDF目錄363903 > W83769 (WINBOND ELECTRONICS CORP) LOCAL BUS IDE SOLUTION PDF資料下載
參數資料
| 型號： | W83769 |
| 廠商： | WINBOND ELECTRONICS CORP |
| 英文描述： | LOCAL BUS IDE SOLUTION |
| 中文描述： | 局部總線IDE解決方案 |
| 文件頁數： | 4/21頁 |
| 文件大小： | 163K |
| 代理商： | W83769 |
W83769
- 4 -
1.2 Chip Decode and Select Logic
The W83769 contains all required chip select and decode logic needed to function without any
additional buffering or interface logic to the local bus. This includes all address decoding, data
buffering, and control logic.
1.3 Direct Drive IDE Disk Interface
The W83769 provides a slew-rate-controlled direct drive interface to four IDE drives. The interface
conforms to relevant industry standards, including the ANSI ATA Rev. 3.0 standard. Up to four
W83769 devices, and therefore 16 IDE drives, can be interfaced to the local bus. Additional drives
can reside on expansion buses. Drive selection and switching are handled by software.
Each device permits either of the two interfaced IDE ports to be assigned and addressed as the
primary or secondary port. Each port can support two drives, which can be assigned as the master
drive (drive 0) or slave drive (drive 1). Individual IDE disk drive performance can be optimized
through the W83769's programmable registers. Each drive's command active and recovery timing,
address setup and hold, and data read/write active and recovery timing may be controlled
independently.
1.4 Four-level Read Ahead Buffer and Counter
The W83769's read-ahead feature significantly enhances disk drive read performance. In pipelined
read-ahead mode, when the host CPU is occupied with other or previous data transfers, the IDE
controller can automatically request and concurrently transfer additional data from the disk drive.
These data are stored in the device's four-level FIFO read-ahead buffer.The controller will continue to
read data from the drive as long as the buffer is not full, the read-ahead counter is not zero, and the
host CPU continues to request data. Data transfer sizes are determined by the host CPU request and
can be word or double-word.
A programmable read-ahead counter is used in conjunction with the read-ahead buffer to regulate the
flow of data from the disk drive. The counter is normally initialized with the number of bytes per
sector. This is determined from the disk formatting and can be different for each drive. As data is
transferred, the counter is decremented to zero. It is then reinitialized for the next sector transfer.
1.5 Four-level Posted Write Buffer
The W83769 also contains a four-level FIFO posted-write buffer which can be used by the CPU to
pipeline data to the disk drive, thereby significantly increasing throughput. The CPU data are written
to the posted-write buffer. Concurrently, data are written to the disk drive by the IDE controller at the
appropriate data transfer rate. While the buffered data are waiting to be written, the CPU is left free to
fetch additional data for the next transfer.
1.6 Interrupt Operation
To ensure proper interrupt operation between the IDE drives and the host CPU, the drives' interrupts
can be passed through the W83769. The interrupts are input on the DIRQ pin and asynchronously
output to the host chipset on the HIRQ pin as IRQ14, the standard IDE PC/AT interrupt. If four drives,
i.e., two drive cables, are present, the interrupts from both pairs of drives can be connected to HIRQ.
The interrupt status of individual drives can be read from the general purpose configuration register,
RX50, bit 2. A 10K ohm pullup should be connected to the HIRQ input to prevent floating.
Alternatively, with four drives present, the interrupt from each pair of drives can be connected directly
to the host CPU chipset IRQ14 and IRQ15.
相關PDF資料 |
PDF描述 |
|---|---|
| W83781D | MONITORING IC |
| W83781 | MONITORING IC |
| W83783 | CABLE ASSEMBLY; BNC MALE TO BNC FEMALE BULKHEAD; 50 OHM, RG188-DS COAX, DOUBLE SHIELDED; 48" CABLE LENGTH; ; *USES STANDARD 50 OHM INTERFACE CONNECTORS* |
| W83783S | MONITORING IC |
| W83787IF | WINBOND I/O WITH SERIAL-INFRARED SUPPORT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W83772G | 功能描述:IC H/W MONITOR 8-TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:2,500 系列:SilentSense™ 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-55°C ~ 125°C，外部傳感器 精確度:±2°C 本地（最大），±3°C 遠程（最大） 拓撲:ADC（三角積分型），比較器，寄存器庫 輸出類型:I²C?/SMBus? 輸出警報:是 輸出風扇:是 電源電壓:2.7 V ~ 5.5 V 工作溫度:-55°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MSOP 包裝:帶卷 (TR) 其它名稱:MIC284-2BMMTRMIC284-2BMMTR-ND |
| W83773G | 制造商:Nuvoton Technology Corp 功能描述:IC H/W MONITOR 8TSSOP |
| W83775G | 制造商:Nuvoton Technology Corp 功能描述:IC H/W MONITOR 8TSSOP |
| W83777F | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Peripheral IC |
| W83781 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:MONITORING IC |
發布緊急采購，3分鐘左右您將得到回復。