- 您現在的位置：買賣IC網 > PDF目錄363894 > W742C813 (WINBOND ELECTRONICS CORP) 4-BIT SINGLE-CHIP MICROCONTROLLER FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROL TRANSMITTER PDF資料下載
參數資料
| 型號： | W742C813 |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 4-BIT SINGLE-CHIP MICROCONTROLLER FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROL TRANSMITTER |
| 中文描述： | 4-BIT, MROM, 3.58 MHz, MICROCONTROLLER, PQFP100 |
| 封裝： | 14 X 20 MM, 2.75 MM HEIGHT, QFP-100 |
| 文件頁數： | 20/56頁 |
| 文件大小： | 455K |
| 代理商： | W742C813 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁
W742E/C813
- 20 -
Fosc/4
Fosc/1024
Enable
Disable
1. Reset
2. CLR EVF,#02H
3. Reset MR0.3 to 0
4.MOV TM0L,R or MOV TM0H,R
8-Bit Binary
Down Counter
(Timer 0)
S
R
Q
HEF.1
IEF.1
Hold mode release (HCF.1)
Timer 0 interrupt (INT1)
1. Reset
2. CLR EVF,#02H
3.Set MR0.3 to 1
EVF.1
MR0.0
Set MR0.3 to 1
4
4
MOV TM0H,R
MOV TM0L,R
Figure 5-6 Organization of Timer 0
5.12.2 Timer 1 (TM1)
Timer 1 (TM1) is also a programmable 8-bit binary down counter, as shown in Figure 5-7. Timer 1 can
output an arbitrary frequency to the MFP pin. The input clock of Timer 1 can be one of three sources:
F
OSC
/64, F
OSC
or F
S
. The source can be selected by setting bit 0 and bit 1 of mode register 1 (MR1).
At initial reset, the Timer 1 clock input is F
OSC.
When the
MOV TM1L, R
or
MOV TM1H, R
instruction
is executed, the specified data are loaded into the auto-reload buffer and the TM1 down-counting will
be disabled that is MR1.3 is reset to 0 at the same time. If the bit 3 of MR1 is set (MR1.3 = 1), the
content of the auto-reload buffer will be loaded into the TM1 down counter, and Timer 1 starts to down
count, and the event flag 7 is reset (EVF.7=0). When the timer decrements to 0FFH, it will generate an
underflow (EVF.7 = 1) and be auto-reloaded with the specified data, after which it will continue to count
down. Then, if interrupt enable flag 7 has been set to 1 (IEF.7 = 1), an interrupt is executed; if hold
mode release enable flag 7 is set to 1 (HEF.7 = 1), the hold state is terminated. The specified
frequency of Timer 1 can be delivered to the MFP output pin by programming bit 2 of MR1. Bit 3 of
MR1 can be used to make Timer 1 stop or start counting.
In a case where Timer 1 clock input is F
T
:
Desired Timer 1 interval = (preset value +1) / F
T
Desired frequency for MFP output pin = F
T
÷
(preset value + 1)
÷
2 (Hz)
Preset value: Decimal number of Timer 1 preset value
F
OSC
: Clock oscillation frequency
相關PDF資料 |
PDF描述 |
|---|---|
| W742C814 | 4-BIT SINGLE-CHIP MICROCONTROLLER FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROL TRANSMITTER |
| W742E813 | 4-BIT MICROCONTROLLER |
| W742C81A | 4-BIT MICROCONTROLLER |
| W742S819 | 4-BIT TELEPHONE CONTROLLER |
| W742S81A | 4-BIT SINGLE-CHIP MICROCONTROLLER FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROL TRANSMITTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W742C814 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:4 BIT MICROCONTROLLER |
| W742C816 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| W742C818 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| W742C81A | 制造商:WINBOND 制造商全稱:Winbond 功能描述:4-BIT MICROCONTROLLER |
| W742CE811 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:4-BIT MICROCONTROLLER |
發布緊急采購，3分鐘左右您將得到回復。