- 您現在的位置：買賣IC網 > PDF目錄363894 > W742C813 (WINBOND ELECTRONICS CORP) 4-BIT SINGLE-CHIP MICROCONTROLLER FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROL TRANSMITTER PDF資料下載
參數資料
| 型號： | W742C813 |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 4-BIT SINGLE-CHIP MICROCONTROLLER FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROL TRANSMITTER |
| 中文描述： | 4-BIT, MROM, 3.58 MHz, MICROCONTROLLER, PQFP100 |
| 封裝： | 14 X 20 MM, 2.75 MM HEIGHT, QFP-100 |
| 文件頁數： | 24/56頁 |
| 文件大小： | 455K |
| 代理商： | W742C813 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁
W742E/C813
- 24 -
5.14 Stop Mode Operation
In stop mode, all operations of the
μ
C cease. The
μ
C enters stop mode when the STOP instruction is
executed and exits stop mode when an external trigger is activated (by a falling signal on the RC or RD
port). When the designated signal is accepted, the
μ
C awakens and executes the next instruction. In
the dual-clock slow operation mode, the STOP instruction will disable both the main-oscillator and sub-
oscillator oscillating; To avoid erroneous execution, the NOP instruction should follow the STOP
command.
5.14.1 Stop Mode Wake-up Enable Flag for RC and RD Port (SEF)
The stop mode wake-up flag for port RC and RD is organized as an 8-bit binary register (SEF.0 to
SEF.7). Before port RC and RD can be used to exit the stop mode, the content of the SEF must be set
first. The SEF is controlled by the
MOV SEF, #I
instruction. The bit descriptions are as follows:
SEF
w
w
w
4
5
6
w
7
w
w
w
0
1
2
w
3
Note: W means write only.
SEF.0 = 1 Device will exit stop mode when a falling edge signal is applied to pin RC.0
SEF.1 = 1 Device will exit stop mode when a falling edge signal is applied to pin RC.1
SEF.2 = 1 Device will exit stop mode when a falling edge signal is applied to pin RC.2
SEF.3 = 1 Device will exit stop mode when a falling edge signal is applied to pin RC.3
SEF.4 = 1 Device will exit stop mode when a falling edge signal is applied to pin RD.0
SEF.5 = 1 Device will exit stop mode when a falling edge signal is applied to pin RD.1
SEF.6 = 1 Device will exit stop mode when a falling edge signal is applied to pin RD.2
SEF.7 = 1 Device will exit stop mode when a falling edge signal is applied to pin RD.3
5.15 Hold Mode Operation
In hold mode, all operations of the
μ
C cease, except for the operation of the oscillator, Timer, Divider,
and LCD driver. The
μ
C enters hold mode when the HOLD instruction is executed. The hold mode can
be released in one of nine ways: by the action of timer 0, timer 1, divider 0, divider 1, RC port, P1.2
(INT0 ), Serial I/O, P1.3 (INT1) and RD port. Before the device enters the hold mode, the HEF, HEFD,
PEF, and IEF flags must be set to control the hold mode release conditions. When any of the HCF bits
is "1," the hold mode will be released. Regarding to RC and RD port, PSR0 and PSR1 registers
indicate signal change on which pin of the port. The HCF and HCFD are set by hardware and clear by
software. When EVF, EVFD and HEF, HEFD have been reset by the
CLR EVF,#I CLR EVFD
and
MOV HEF,#I
CLR HEFD
instructions, the corresponding bit of HCF, HCFD is reset simultaneously.
The HCF and HCFD should be clear every time before enter the hold mode. For more details, refer to
the following flow chart.
相關PDF資料 |
PDF描述 |
|---|---|
| W742C814 | 4-BIT SINGLE-CHIP MICROCONTROLLER FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROL TRANSMITTER |
| W742E813 | 4-BIT MICROCONTROLLER |
| W742C81A | 4-BIT MICROCONTROLLER |
| W742S819 | 4-BIT TELEPHONE CONTROLLER |
| W742S81A | 4-BIT SINGLE-CHIP MICROCONTROLLER FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROL TRANSMITTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W742C814 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:4 BIT MICROCONTROLLER |
| W742C816 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| W742C818 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| W742C81A | 制造商:WINBOND 制造商全稱:Winbond 功能描述:4-BIT MICROCONTROLLER |
| W742CE811 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:4-BIT MICROCONTROLLER |
發布緊急采購，3分鐘左右您將得到回復。