- 您現在的位置：買賣IC網 > PDF目錄363894 > W742C813 (WINBOND ELECTRONICS CORP) 4-BIT SINGLE-CHIP MICROCONTROLLER FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROL TRANSMITTER PDF資料下載
參數資料
| 型號： | W742C813 |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 4-BIT SINGLE-CHIP MICROCONTROLLER FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROL TRANSMITTER |
| 中文描述： | 4-BIT, MROM, 3.58 MHz, MICROCONTROLLER, PQFP100 |
| 封裝： | 14 X 20 MM, 2.75 MM HEIGHT, QFP-100 |
| 文件頁數： | 32/56頁 |
| 文件大小： | 455K |
| 代理商： | W742C813 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁當前第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁
W742E/C813
- 32 -
5.18 Serial I/O interface
The bit 0 and bit 1 of port P0 can be used as a serial input/output port. P0.0 is the serial clock I/O pin
and P0.1 is the serial data I/O pin. A 4-bit binary register, Serial Interface Control register (SIC),
controls the serial port. SIC is controlled by the
MOV SIC,#I
instruction. The bit definition is as follow:
SIC
w
w
w
0
1
2
w
3
Bit 0 = 0 P0.0 & P0.1 work as normal input/output pin;
Bit 0 = 1 P0.0 & P0.1 work as serial port function.
Bit 1 = 0 P0.0 works as serial clock input pin;
Bit 1 = 1 P0.0 works as serial clock output pin.
Bit 2 = 0 Serial data latched/changed at falling edge of clock;
Bit 2 = 1 Serial data latched/changed at rising edge of clock.
Bit 3 = 0 Serial clock output frequency is fosc/2;
Bit 3 = 1 Serial clock output frequency is fosc/256.
At initial reset, SIC = 0000B.
The serial I/O functions are controlled by the instructions
SOP R
and
SIP R
. The two instructions are
described below:
(1) When in the first time the SIP R instruction is executed, the data will be loaded to the ACC and
RAM from the serial input buffer. But this data is not meaningful, it is used to enable serial port.
There are two methods to get the serial data, one is interrupt and the other is polling. When enable
the serial input, the bit 1 of port status register 2 (PRS2) will automatically be set to "1" (BUSY
I
= 1).
Then the P0.0 pin will send out 8 clocks or accept 8 clocks from external device and the data from
the P0.1 pin will be loaded to SIB buffer at the rising or falling edge of the P0.0 pin. After the 8
clocks have been sent, BUSY
I
will be reset to "0" and EVF.5 will be set to "1." At this time, if IEF.5
has been set (IEF.5 = 1), an interrupt is executed then the SIP R instruction can get the correct
data from the serial input buffer (SIB), low nibble of SIB moves to ACC register and the high nibble
moves to RAM; if HEF.5 has been set (HEF.5 = 1), the hold state is terminated. The polling method
is to check the status of PSR2.1 (BUSY
I
) to know whether the serial input process is completed or
not. If a serial input process is not completed, but the SIP R instruction is executed again, the data
will be lost. The timing is shown in Figure 5-12.
相關PDF資料 |
PDF描述 |
|---|---|
| W742C814 | 4-BIT SINGLE-CHIP MICROCONTROLLER FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROL TRANSMITTER |
| W742E813 | 4-BIT MICROCONTROLLER |
| W742C81A | 4-BIT MICROCONTROLLER |
| W742S819 | 4-BIT TELEPHONE CONTROLLER |
| W742S81A | 4-BIT SINGLE-CHIP MICROCONTROLLER FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROL TRANSMITTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W742C814 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:4 BIT MICROCONTROLLER |
| W742C816 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| W742C818 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| W742C81A | 制造商:WINBOND 制造商全稱:Winbond 功能描述:4-BIT MICROCONTROLLER |
| W742CE811 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:4-BIT MICROCONTROLLER |
發布緊急采購，3分鐘左右您將得到回復。