- 您現在的位置：買賣IC網 > PDF目錄363895 > W77E58F-25 (WINBOND ELECTRONICS CORP) 8 BIT MICROCONTROLLER PDF資料下載
參數資料
| 型號： | W77E58F-25 |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8 BIT MICROCONTROLLER |
| 中文描述： | 8-BIT, FLASH, 25 MHz, MICROCONTROLLER, PQFP44 |
| 封裝： | QFP-44 |
| 文件頁數： | 63/85頁 |
| 文件大小： | 570K |
| 代理商： | W77E58F-25 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁當前第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁
Preliminary W77E58
Publication Release Date: March 1999
- 63 - Revision A1
RWT:
WDCON.0 - Reset Watchdog Timer. This bit is used to clear the Watchdog timer and to
restart it. This bit is self-clearing, so after the software writes 1 to it the hardware will
automatically clear it. If the Watchdog timer reset is enabled, then the RWT has to be set by
the user within 512 clocks of the time-out. If this is not done then a Watchdog timer reset will
occur.
CLOCK CONTROL
WD1, WD0: CKCON.7, CKCON.6 - Watchdog Timer Mode select bits. These two bits select the time-
out interval for the watchdog timer. The reset time is 512 clock longer than the interrupt
time-out value.
The default Watchdog time-out is 2
17
clocks, which is the shortest time-out period. The EWT, WDIF
and RWT bits are protected by the Timed Access procedure. This prevents software from accidentally
enabling or disabling the watchdog timer. More importantly, it makes it highly improbable that errant
code can enable or disable the watchdog timer.
SERIAL PORT
Serial port in the W77E58 is a full duplex port. The W77E58 provides the user with additional features
such as the Frame Error Detection and the Automatic Address Recognition. The serial ports are
capable of synchronous as well as asynchronous communication. In Synchronous mode the W77E58
generates the clock and operates in a half duplex mode. In the asynchronous mode, full duplex
operation is available. This means that it can simultaneously transmit and receive data. The transmit
register and the receive buffer are both addressed as SBUF Special Function Register. However any
write to SBUF will be to the transmit register, while a read from SBUF will be from the receive buffer
register. The serial port can operate in four different modes as described below.
MODE 0
This mode provides synchronous communication with external devices. In this mode serial data is
transmitted and received on the RXD line. TXD is used to transmit the shift clock. The TxD clock is
provided by the W77E58 whether the device is transmitting or receiving. This mode is therefore a half
duplex mode of serial communication. In this mode, 8 bits are transmitted or received per frame. The
LSB is transmitted/received first. The baud rate is fixed at 1/12 or 1/4 of the oscillator frequency. This
baud rate is determined by the SM2 bit (SCON.5). When this bit is set to 0, then the serial port runs at
1/12 of the clock. When set to 1, the serial port runs at 1/4 of the clock. This additional facility of
programmable baud rate in mode 0 is the only difference between the standard 8051 and the
W77E58.
The functional block diagram is shown below. Data enters and leaves the Serial port on the RxD line.
The TxD line is used to output the shift clock. The shift clock is used to shift data into and out of the
W77E58 and the device at the other end of the line. Any instruction that causes a write to SBUF will
start the transmission. The shift clock will be activated and data will be shifted out on the RxD pin till
all 8 bits are transmitted. If SM2 = 1, then the data on RxD will appear 1 clock period before the
falling edge of shift clock on TxD. The clock on TxD then remains low for 2 clock periods, and then
goes high again. If SM2 = 0, the data on RxD will appear 3 clock periods before the falling edge of
shift clock on TxD. The clock on TxD then remains low for 6 clock periods, and then goes high again.
This ensures that at the receiving end the data on RxD line can either be clocked on the rising edge
of the shift clock on TxD or latched when the TxD clock is low.
相關PDF資料 |
PDF描述 |
|---|---|
| W77E58F-40 | 8 BIT MICROCONTROLLER |
| W77E58P-25 | 8 BIT MICROCONTROLLER |
| W77E58P-40 | 8 BIT MICROCONTROLLER |
| W77IC32-25 | 8 BIT MICROCONTROLLER |
| W77IC32P-25 | 8 BIT MICROCONTROLLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W77E58F-40 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8 BIT MICROCONTROLLER |
| W77E58P-25 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8 BIT MICROCONTROLLER |
| W77E58P-40 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8 BIT MICROCONTROLLER |
| W77I058A | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-BIT MICROCONTROLLER |
| W77I058A25DL | 功能描述:IC MCU 8-BIT 32K FLASH 40-DIP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:W77 標準包裝:250 系列:80C 核心處理器:8051 芯體尺寸:8-位 速度:16MHz 連通性:EBI/EMI，I²C，UART/USART 外圍設備:POR，PWM，WDT 輸入/輸出數:40 程序存儲器容量:- 程序存儲器類型:ROMless EEPROM 大小:- RAM 容量:256 x 8 電壓 - 電源 (Vcc/Vdd):4.5 V ~ 5.5 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:68-LCC（J 形引線） 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。