- 您現在的位置：買賣IC網 > PDF目錄363903 > W83787IF (WINBOND ELECTRONICS CORP) WINBOND I/O WITH SERIAL-INFRARED SUPPORT PDF資料下載
參數資料
| 型號： | W83787IF |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | 外設及接口 |
| 英文描述： | WINBOND I/O WITH SERIAL-INFRARED SUPPORT |
| 中文描述： | MULTIFUNCTION PERIPHERAL, PQFP100 |
| 封裝： | PLASTIC, QFP-100 |
| 文件頁數： | 20/123頁 |
| 文件大?。?/td> | 1751K |
| 代理商： | W83787IF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁
W83787IF
Publication Release Date:Sep 1995
- 20 -
Revision A1
2.0 FDC FUNCTIONAL DESCRIPTION
2.1 W83787IF FDC
The floppy disk controller of the W83787IF integrates all of the logic required for floppy disk
control.The FDC includes the following blocks: AT interface, Precompensation, Data Rate Selection,
Digital Data Separator, and FDC Core.
2.1.1 AT interface
The interface consists of the standard asynchronous signals: /RD, /WR, A0-A3, IRQ, DMA control,
and a data bus. The address lines select between the configuration registers, the FIFO and
control/status registers.
2.1.2 Data Separator
The function of the data separator is to lock onto the incoming serial read data. When a lock is
achieved the serial front end logic of the chip is provided with a clock which is synchronized to the
read data. The synchronized clock, called the Data Window, is used to internally sample the serial
data portion of the bit cell, and the alternate state samples the clock portion. Serial to parallel
conversion logic separates the read data into clock and data bytes.
The Digital Data Separator (DDS) has three parts: control logic, error adjustment, and speed tracking.
The DDS circuit cycles once every 12 clock cycles ideally. Any data pulse input will be synchronized
and then adjusted by immediate error adjustment. The control logic will generate RDD and RWD for
every pulse input. During any cycle where no data pulse is present, the DDS cycles are based on
speed. A digital integrator is used to keep track of the speed changes in the input data stream.
2.1.3 Write Precompensation
The write precompensation logic is used to minimize bit shifts in the RDDATA stream from the disk
drive. Shifting of bits is a known phenomenon in magnetic media and is dependent on the disk media
and the floppy drive.
The FDC monitors the bit stream that is being sent to the drive. The data patterns that require
precompensation are well known. Depending upon the pattern, the bit is shifted either early or late
relative to the surrounding bits.
2.1.4 FDC Core
The W83787IF FDC is capable of performing sixteen commands. Each command is initiated by a
multi-byte transfer from the microprocessor. The result can also be a multi-byte transfer back to the
microprocessor. Each command consists of three phases: command, execution, and result.
Command
The microprocessor issues all required information to the controller to perform a specific operation.
Execution
The controller performs the specified operation.
Result
After the operation is completed, status information and other housekeeping information is provided
to the microprocessor.
相關PDF資料 |
PDF描述 |
|---|---|
| W83787F | WINBOND I/O WITH SERIAL-INFRARED SUPPORT |
| W83791D | W83791D Winbond H/W Monitoring IC |
| W83791SD | H/W MONITORING IC |
| W83791SG | H/W MONITORING IC |
| W83877AF | Multi-Function I/O Port Controller(多功能輸入／輸出口控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W83791D | 制造商:WINBOND 制造商全稱:Winbond 功能描述:Winbond H/W Monitoring IC |
| W83791G | 功能描述:IC MONITOR H/W 48-LQFP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓?fù)?ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| W83791SD | 制造商:WINBOND 制造商全稱:Winbond 功能描述:H/W MONITORING IC |
| W83791SG | 制造商:WINBOND 制造商全稱:Winbond 功能描述:H/W MONITORING IC |
| W83792AD | 制造商:WINBOND 制造商全稱:Winbond 功能描述:H/W Monitoring IC (CSB Version) |
發布緊急采購，3分鐘左右您將得到回復。