- 您現在的位置：買賣IC網 > PDF目錄363903 > W83787IF (WINBOND ELECTRONICS CORP) WINBOND I/O WITH SERIAL-INFRARED SUPPORT PDF資料下載
參數資料
| 型號： | W83787IF |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | 外設及接口 |
| 英文描述： | WINBOND I/O WITH SERIAL-INFRARED SUPPORT |
| 中文描述： | MULTIFUNCTION PERIPHERAL, PQFP100 |
| 封裝： | PLASTIC, QFP-100 |
| 文件頁數： | 50/123頁 |
| 文件大小： | 1751K |
| 代理商： | W83787IF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁當前第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁
W83787IF
Publication ReleaseDate:Sep 1995
- 50 -
Revision A1
A watchdog timer is required to prevent system lockup. The timer indicates that more than 10
μ
S
have elapsed from the start
of the EPP
cycle to
the time
WAIT
is deasserted. The current EPP cycle
is aborted when a timeout occurs. The timeout condition is indicated in Status bit 0.
EPP Operation
The EPP operates on a two-phase cycle. First, the host selects the register within the device for
subsequent operations. Second, the host performs a series of read and/or write byte operations to the
selected register. Four operations are supported on the EPP: Address Write, Data Write, Address
Read, and Data Read. All operations on the EPP device are performed asynchronously.
EPP Version 1.9 Operation
The EPP read/write operation can be completed under the following conditions:
a. If the nWait is active low, when the read cycle (nWrite inactive high, nDStrb/nAStrb active low) or
write cycle (nWrite active low, nDStrb/nAStrb active low) starts, the read/write cycle proceeds
normally and will be completed when nWait goes inactive high.
b. If nWait is inactive high, the read/write cycle will not start. It must wait until nWait changes to
active low, at which time it will start as described above.
EPP Version 1.7 Operation
The EPP read/write cycle can start without checking whether nWait is active or inactive. Once the
read/write cycle starts, however, it will not terminate until nWait changes from active low to inactive
high.
5.2.9 EPP Address Selection
More than four register addresses are required for EPP operation, so parallel port address 3BCh will
not support EPP mode when the parallel port is set up for W83757 mode or ECP mode, the SPP/BPP
will function normally in 3BCh, 378h, 278h. If 3BCh and EPP mode are selected, then the
SPP/BPP/EPP function will not be active.
5.3 Extended Capabilities Parallel (ECP) Port
This
port is software and hardware compatible with existing parallel ports, so it may be used as a
standard printer mode if ECP is not required. It provides an automatic high burst-bandwidth channel
that supports DMA for ECP in both the forward (host to peripheral) and reverse (peripheral to host)
directions.
Small FIFOs are used in both forward and reverse directions to improve the maximum bandwidth
requirement. The size of the FIFO is 16 bytes. The ECP port supports an automatic handshake for
the standard parallel port to improve compatibility mode transfer speed.
The ECP port supports run-length-encoded (RLE) decompression (required) in hardware.
Compression is accomplished by counting identical bytes and transmitting an RLE byte that indicates
how many times the next byte is to be repeated. Hardware support for compression is optional.
For more information about the ECP Protocol, refer to the Extended Capabilities Port Protocol and
ISA Interface Standard.
相關PDF資料 |
PDF描述 |
|---|---|
| W83787F | WINBOND I/O WITH SERIAL-INFRARED SUPPORT |
| W83791D | W83791D Winbond H/W Monitoring IC |
| W83791SD | H/W MONITORING IC |
| W83791SG | H/W MONITORING IC |
| W83877AF | Multi-Function I/O Port Controller(多功能輸入／輸出口控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W83791D | 制造商:WINBOND 制造商全稱:Winbond 功能描述:Winbond H/W Monitoring IC |
| W83791G | 功能描述:IC MONITOR H/W 48-LQFP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓?fù)?ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| W83791SD | 制造商:WINBOND 制造商全稱:Winbond 功能描述:H/W MONITORING IC |
| W83791SG | 制造商:WINBOND 制造商全稱:Winbond 功能描述:H/W MONITORING IC |
| W83792AD | 制造商:WINBOND 制造商全稱:Winbond 功能描述:H/W Monitoring IC (CSB Version) |
發布緊急采購，3分鐘左右您將得到回復。