- 您現在的位置：買賣IC網 > PDF目錄363904 > W89C92 (WINBOND ELECTRONICS CORP) PCMCIA ETHERNET NETWORK TWISTED PAIR INTERFACE CONTROLLER PDF資料下載
參數資料
| 型號： | W89C92 |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | 網絡接口 |
| 英文描述： | PCMCIA ETHERNET NETWORK TWISTED PAIR INTERFACE CONTROLLER |
| 中文描述： | DATACOM, ETHERNET TRANSCEIVER, PDIP16 |
| 封裝： | DIP-16 |
| 文件頁數： | 18/48頁 |
| 文件大小： | 395K |
| 代理商： | W89C92 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
W89C926 PENTIC+
- 18 -
BIT
SYMBOL
DESCRIPTION
0-5
-
Reserved. Must be 0s.
6
EW/ER
EEPROM Write/Read Select.
This bit selects the EEPROM read/write sequence. If EW/ER = 1, the
write sequence is selected. If EW/ER = 0, the read sequence is selected.
7
EOS
EEPROM Operation Select.
This bit enables the EEPROM read/write sequence. If EOS = 1, the
EEPROM read/write sequence will be started. EOS is reset if the
read/write sequence is finished or aborted.
EEPROM Address/Data Register (ADR)
This register is located on page 3 and is used for EEPROM address or data transfer during EEPROM
access.
Access Address: IOBase + 04H
Access Type: I/O Read/Write
POWER-ON INITIALIZATION AND AUTO-LOADING PROCESS
When powered on, the system should reset the card first, as required by the PCMCIA specifications.
The reset signal will trigger a number of internal operations: First, the PENTIC+ monitors the
EECS/FCS pin to determined where the configurations are stored. If this pin is pulled high, the
configurations are stored in the flash memory; if it is pulled low, they are stored in an EEPROM.
Then, within 10ms after the reset pulse is negated, the PENTIC+ will automatically load the
configurations, ID, and CIS data into the LAN configuration registers and the upper half of SRAM (if
an EEPROM is used). During this auto-load procedure the PENTIC+ will assert IREQ low for
Rdy/Bsy signaling, since the socket is configured at the memory-only interface during initialization.
Note that this auto-load operation occurs only after a hardware reset pulse. A software reset
(including setting COR.SRESET = 1) will not invoke this operation.
EECS/FCS Pulled High
If EECS/FCS is pulled high, this indicates that the configurations are stored in a flash memory.
Accordingly, after a power-on reset the PENTIC+ will automatically load the LAN configuration
registers from flash memory. The Ethernet IDs stored in the flash memory will be mapped into ID
registers automatically when they are read.
相關PDF資料 |
PDF描述 |
|---|---|
| W89C926 | PCMCIA ETHERNET NETWORK TWISTED PAIR INTERFACE CONTROLLER |
| W89C926F | 10M PCMCIA Ethernet Network Interface Controller |
| W89C940 | ELANC-PCI (TWISTED-PAIR ETHER-LAN CONTROLLER WITH PCI INTERFACE) |
| W89C982 | INTEGRATED MULTIPLE REPEATER II |
| W89C982AF | INTEGRATED MULTIPLE REPEATER II |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W89C926 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:PCMCIA ETHERNET NETWORK TWISTED PAIR INTERFACE CONTROLLER |
| W89C926F | 制造商:WINBOND 制造商全稱:Winbond 功能描述:10M PCMCIA Ethernet Network Interface Controller |
| W89C926PENTIC+ | 制造商:WINBOND 制造商全稱:Winbond 功能描述:PCMCIA ETHERNET NETWORK TWISTED PAIR INTERFACE CONTROLLER |
| W89C92P | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:10M CMOS Coaxial Transceiver |
| W89C940 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:ELANC-PCI (TWISTED-PAIR ETHER-LAN CONTROLLER WITH PCI INTERFACE) |
發布緊急采購，3分鐘左右您將得到回復。