- 您現在的位置：買賣IC網 > PDF目錄363901 > W79E802A (WINBOND ELECTRONICS CORP) 8-BIT MICROCONTROLLER PDF資料下載
參數資料
| 型號： | W79E802A |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | 8位微控制器 |
| 英文描述： | 8-BIT MICROCONTROLLER |
| 中文描述： | 8位微控制器 |
| 文件頁數： | 105/115頁 |
| 文件大?。?/td> | 1456K |
| 代理商： | W79E802A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁當前第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁
W79E804A/803A/802A
Publication Release Date: July 16, 2007
- 105 -
Revision A2
25. ICP (IN-CIRCUIT PROGRAM) FLASH PROGRAM
The contexts of flash in W79E804 series are empty by default. User must program the flash EPROM
by external Writer device or by ICP (In-Circuit Program) tool.
In the ICP tool, the user must take note of ICP’s program pins used in system board. In some
application circuits, the pins are located at P1.5, P0.4 and P0.5, as below figure. During ICP
programming, P1.5 must be set to high voltage (~10.5V), and keeping this voltage to update code,
data and/or configure CONFIG bits. After programming completion, the high voltage of P1.5 should be
released. So, it is highly recommended user power off then power on after ICP programming has
completed on the system board.
Upon entry into ICP program mode, all pin will be set to quasi-bidirectional mode, and output to level
“1”.
The W79E804 series support programming of Flash EPROM (
8K/4K/2K
bytes AP Flash EPROM) and
NVM data memory (
256
bytes). User has the option to program the AP flash and NVM either
individually or both.
Figure
25-1: Application Circuit of ICP
Note:
1. When using ICP to upgrade code, the P1.5, P0.4 and P0.5 must be taken within design system board.
2. After program finished by ICP, to suggest system power must power off and remove ICP connector then power on.
3.
It is recommended that user performs erase function and programming configure bits continuously without
any interruption.
相關PDF資料 |
PDF描述 |
|---|---|
| W79E802ADG | 8-BIT MICROCONTROLLER |
| W79E802ASG | 8-BIT MICROCONTROLLER |
| W79E803 | 8-BIT MICROCONTROLLER |
| W79E803A | 8-BIT MICROCONTROLLER |
| W79E803ADG | 8-BIT MICROCONTROLLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W79E802ADG | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-BIT MICROCONTROLLER |
| W79E802ASG | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-BIT MICROCONTROLLER |
| W79E803 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-BIT MICROCONTROLLER |
| W79E803A | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-BIT MICROCONTROLLER |
| W79E803ADG | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-BIT MICROCONTROLLER |
發布緊急采購，3分鐘左右您將得到回復。