- 您現在的位置：買賣IC網 > PDF目錄363901 > W79E804A (WINBOND ELECTRONICS CORP) 8-BIT MICROCONTROLLER PDF資料下載
參數資料
| 型號： | W79E804A |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | 8位微控制器 |
| 英文描述： | 8-BIT MICROCONTROLLER |
| 中文描述： | 8位微控制器 |
| 文件頁數： | 97/115頁 |
| 文件大小： | 1456K |
| 代理商： | W79E804A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁當前第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁
W79E804A/803A/802A
Publication Release Date: July 16, 2007
- 97 -
Revision A2
24.2.3 The Control Register, I2CON
The CPU can read from and write to this 8-bit, directly addressable SFR. Two bits are affected by
hardware: the SI bit is set when the I2C hardware requests a serial interrupt, and the STO bit is
cleared when a STOP condition is present on the bus. The STO bit is also cleared when ENS = "0".
ENSI
Set to enable I2C serial function block. When ENS=1 the I2C serial function enables. The
port latches of SDA1 and SCL1 must be set to logic high.
STA
I2C START Flag. Setting STA to logic 1 to enter master mode, the I2C hardware sends a
START or repeat START condition to bus when the bus is free.
STO
I2C STOP Flag. In master mode, setting STO to transmit a STOP condition to bus then
I2C hardware will check the bus condition if a STOP condition is detected this flag will be
cleared by hardware automatically. In a slave mode, setting STO resets I2C hardware to
the defined “not addressed” slave mode. This means it is NO LONGER in the slave
receiver mode to receive data from the master transmit device.
SI
I2C Port 1 Interrupt Flag. When a new SIO state is present in the S1STA register, the SI
flag is set by hardware, and if the EA and EI2C1 bits are both set, the I2C1 interrupt is
requested. SI must be cleared by software.
AA
Assert Acknowledge control bit. When AA=1 prior to address or data received, an
acknowledged (low level to SDA) will be returned during the acknowledge clock pulse on
the SCL line when 1.) A slave is acknowledging the address sent from master, 2.) The
receiver devices are acknowledging the data sent by transmitter. When AA=0 prior to
address or data received, a Not acknowledged (high level to SDA) will be returned during
the acknowledge clock pulse on the SCL line.
24.2.4 The Status Register, I2STATUS
I2STATUS is an 8-bit read-only register. The three least significant bits are always 0. The five most
significant bits contain the status code. There are 23 possible status codes. When I2STATUS contains
F8H, no serial interrupt is requested. All other I2STATUS values correspond to defined SIO states.
When each of these states is entered, a status interrupt is requested (SI = 1). A valid status code is
present in I2STATUS one machine cycle after SI is set by hardware and is still present one machine
cycle after SI has been reset by software.
24.2.5 The I2C Clock Baud Rate Bits, I2CLK
The data baud rate of I2C is determines by I2CLK register when SIO is in a master mode. It is not
important when SIO is in a slave mode. In the slave modes, SIO will automatically synchronize with
any clock frequency up to 400 KHz from master I2C device.
The data baud rate of I2C setting is Data Baud Rate of I2C = Fcpu / (I2CLK+1). The Fcpu=Fosc/4. If
Fosc = 16MHz, the I2CLK = 40(28H), so data baud rate of I2C = 16MHz/(4X (40 +1)) =
97.56Kbits/sec. The block diagram is as below figure.
相關PDF資料 |
PDF描述 |
|---|---|
| W79E804ADG | 8-BIT MICROCONTROLLER |
| W79E804ASG | 8-BIT MICROCONTROLLER |
| W80NF06 | N-CHANNEL 60V - 0.0065OHM - 80A TO-220/D2PAK/TO-247 STripFET II POWER MOSFET |
| W81181AD | USB HUB CONTROLLER |
| W81181D | USB HUB CONTROLLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W79E804ADG | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-BIT MICROCONTROLLER |
| W79E804ASG | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-BIT MICROCONTROLLER |
| W79E8213 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:W79E8213中文資料 |
| W79E8213_W79E8213R | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Table of contents- |
| W79E8213AKG | 制造商:Nuvoton Technology Corp 功能描述:IC MCU 8BIT 4K FLASH 20DIP |
發布緊急采購，3分鐘左右您將得到回復。