- 您現在的位置：買賣IC網 > PDF目錄363903 > W83787F (WINBOND ELECTRONICS CORP) WINBOND I/O WITH SERIAL-INFRARED SUPPORT PDF資料下載
參數資料
| 型號： | W83787F |
| 廠商： | WINBOND ELECTRONICS CORP |
| 英文描述： | WINBOND I/O WITH SERIAL-INFRARED SUPPORT |
| 中文描述： | 華邦的I /串行O型紅外線支持 |
| 文件頁數： | 47/123頁 |
| 文件大小： | 1751K |
| 代理商： | W83787F |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁當前第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁
W83787IF
Publication ReleaseDate:Sep 1995
- 47 -
Revision A1
5.2.1 Data Swapper
The system microprocessor can read the contents of the printer's data latch by reading the data
swapper.
5.2.2 Printer Status Buffer
The system microprocessor can read the printer status by reading the address of the printer status
buffer. The bit definitions are as follows:
1
1
1
2
3
5
4
6
7
0
TMOUT
ERROR
SLCT
PE
ACK
BUSY
Notes:
Bit 7: This signal is active during data entry, when the printer is off-line during printing, when the print
head is changing position, or during an error state. When this signal is active, the printer is
busy
and cannot accept data.
Bit 6: This bit represents the current state of the printer's
ACK
signal. A 0 means the printer has
received a character and is ready to accept another. Normally, this signal will be active for
approximately 5
microseconds before
BUSY
stops.
Bit 5: A 1 means the printer has detected the end of paper.
Bit 4: A 1 means the printer is selected.
Bit 3: A 0 means the printer has encountered an error condition.
Bit 1, 2: These two bits are not implemented and are logic one during a read of the status register.
Bit 0: This bit is valid in EPP mode only. It indicates that a 10
μ
S timeout has occurred on the EPP
bus. A logic 0 means that no timeout error has occurred; a logic 1 means that a timeout error
has been detected. Writing a logic 1 to this bit will clear the timeout status bit; writing a logic 0
has no effect.
5.2.3 Printer Control Latch and Printer Control Swapper
The system microprocessor can read the contents of the printer control latch by reading the printer
control swapper. Bit definitions are as follows:
1
1
1
2
3
4
5
6
7
0
STROBE
AUTO FD
INIT
SLCT IN
IRQ ENABLE
DIR
Notes:
Bit 7, 6: These two bits are a logic one during a read. They can be written.
Bit 5: Direction control bit
相關PDF資料 |
PDF描述 |
|---|---|
| W83791D | W83791D Winbond H/W Monitoring IC |
| W83791SD | H/W MONITORING IC |
| W83791SG | H/W MONITORING IC |
| W83877AF | Multi-Function I/O Port Controller(多功能輸入／輸出口控制器) |
| W83877ATD | enhanced version from Winbonds most popular I/O chip W83877F |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W83787IF | 制造商:WINBOND 制造商全稱:Winbond 功能描述:WINBOND I/O WITH SERIAL-INFRARED SUPPORT |
| W83791D | 制造商:WINBOND 制造商全稱:Winbond 功能描述:Winbond H/W Monitoring IC |
| W83791G | 功能描述:IC MONITOR H/W 48-LQFP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| W83791SD | 制造商:WINBOND 制造商全稱:Winbond 功能描述:H/W MONITORING IC |
| W83791SG | 制造商:WINBOND 制造商全稱:Winbond 功能描述:H/W MONITORING IC |
發布緊急采購，3分鐘左右您將得到回復。