- 您現在的位置：買賣IC網 > PDF目錄363903 > W83787F (WINBOND ELECTRONICS CORP) WINBOND I/O WITH SERIAL-INFRARED SUPPORT PDF資料下載
參數資料
| 型號： | W83787F |
| 廠商： | WINBOND ELECTRONICS CORP |
| 英文描述： | WINBOND I/O WITH SERIAL-INFRARED SUPPORT |
| 中文描述： | 華邦的I /串行O型紅外線支持 |
| 文件頁數： | 60/123頁 |
| 文件大小： | 1751K |
| 代理商： | W83787F |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁當前第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁
W83787IF
Publication ReleaseDate:Sep 1995
- 60 -
Revision A1
5.7 Joystick Mode*
The joystick mode allows users to plug a joystick into the parallel port DB-25 connector. The pin
definitions are shown in Table 5-1.
Pins NSTB
,
AFD
,
NSLIN
,
and
INIT
output high as a voltage supply to the joystick.
Pins PD5 and PD4 are the button input of the joystick.
Pins PD1 and PD0 are the X/Y axis paddle input of the joystick.
There are two one-shot timers (556) inside the W83787IF for use with the joystick.
6.0 GAME PORT DECODER
The W83787IF provides
GMRD
and
GMWR
pins that decode address 201H and I/O read/write
commands.
If the host issues IOR 201H, the
GMRD
pin is
low active; if it issues IOW 201H, the
GMWR
pin is low
active.
7.0 EXTENDED FUNCTION REGISTERS
The W83787IF provides many configuration registers for setting up different types of configurations.
After power-on reset, the state of the hardware setting of each pin will be latched by the relevant
configuration register to allow the W83787IF to enter the proper operating configuration. To protect
the chip from invalid reads or writes, the configuration registers cannot be accessed by the user. To
enable the configuration registers to be read and written, first the value 89H/88H must be written to
the Extended Functions Enable Register (I/O port address 250H). Second, a value from 00H to 0BH
must be written to the Extended Functions Index Register (I/O port address 251H) to identify which
configuration register is to be accessed. The user can then access the desired configuration register
through the Extended Functions Data Register (I/O port address 252H). After programming of the
configuration register is finished, a value other than 89H/88H should be written to EFER or bit 6 of
CR9 (LOCKREG) should be set to high to protect the configuration registers against accidental
accesses. The configuration registers can be reset to their default or hardware setting values only by
a cold reset (pin MR = 1). A warm reset will not affect the configuration registers.
7.1 Extended Functions Enable Register (EFER)
After a power-on reset, the W83787IF enters the default operating mode. Before the W83787IF
enters the Extended Function mode, a 89H/88H (dependent on power-on setting value of pin GMRD)
must be programmed to the Extended Function Enable Register (EFER) so that the extended
function register can be accessed. The Extended Function Enable Register is a write-only register. Its
port address is 250H on a PC/AT system.
7.2 Extended Function Index Register(EFIR), Extended Function Data Register
(EFDR)
After 89H/88H is programmed into EFER, the Extended Function Index Register (EFIR) must be
loaded with index value 0H, 1H, 2H, ..., or AH to access Configuration Register 0 (CR0),
Configuration Register 1 (CR1), Configuration Register 2 (CR2), ..., or Configuration Register A
(CRA) through the Extended Function Data Register (EFDR). EFIR is a write-only register with port
address 251H on PC/AT systems; EFDR is a read/write register with port address 252H on PC/AT
systems. The function of each configuration register is described below.
相關PDF資料 |
PDF描述 |
|---|---|
| W83791D | W83791D Winbond H/W Monitoring IC |
| W83791SD | H/W MONITORING IC |
| W83791SG | H/W MONITORING IC |
| W83877AF | Multi-Function I/O Port Controller(多功能輸入／輸出口控制器) |
| W83877ATD | enhanced version from Winbonds most popular I/O chip W83877F |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W83787IF | 制造商:WINBOND 制造商全稱:Winbond 功能描述:WINBOND I/O WITH SERIAL-INFRARED SUPPORT |
| W83791D | 制造商:WINBOND 制造商全稱:Winbond 功能描述:Winbond H/W Monitoring IC |
| W83791G | 功能描述:IC MONITOR H/W 48-LQFP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| W83791SD | 制造商:WINBOND 制造商全稱:Winbond 功能描述:H/W MONITORING IC |
| W83791SG | 制造商:WINBOND 制造商全稱:Winbond 功能描述:H/W MONITORING IC |
發布緊急采購，3分鐘左右您將得到回復。