- 您現在的位置：買賣IC網 > PDF目錄363903 > W83787F (WINBOND ELECTRONICS CORP) WINBOND I/O WITH SERIAL-INFRARED SUPPORT PDF資料下載
參數資料
| 型號： | W83787F |
| 廠商： | WINBOND ELECTRONICS CORP |
| 英文描述： | WINBOND I/O WITH SERIAL-INFRARED SUPPORT |
| 中文描述： | 華邦的I /串行O型紅外線支持 |
| 文件頁數： | 57/123頁 |
| 文件大小： | 1751K |
| 代理商： | W83787F |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁當前第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁
W83787IF
Publication ReleaseDate:Sep 1995
- 57 -
Revision A1
ECP Pin descriptions, continued
NAME
TYPE
DESCRIPTION
nFault (nPeriphRequest)
I
Generates an error interrupt when it is asserted. This signal is
valid only in the forward direction. The peripheral is permitted
(but not required) to drive this pin low to request a reverse
transfer during ECP Mode.
nInit (nReverseRequest)
O
This signal sets the transfer direction (asserted = reverse,
deasserted = forward). This pin is driven low to place the
channel in the reverse direction.
nSelectIn (ECPMode)
O
This signal is always deasserted in ECP mode.
5.3.13 ECP Operation
The host must negotiate on the parallel port to determine if the peripheral supports the ECP protocol
before ECP operation. After negotiation, it is necessary to initialize some of the port bits. The
following are required:
(a) Set direction = 0, enabling the drivers.
(b) Set strobe = 0, causing the nStrobe signal to default to the deasserted state.
(c) Set autoFd = 0, causing the nAutoFd signal to default to the deasserted state.
(d) Set mode = 011 (ECP Mode)
ECP address/RLE bytes or data bytes may be sent automatically by writing the ecpAFifo or ecpDFifo,
respectively.
Mode Switching
Software will execute P1284 negotiation and all operation prior to a data transfer phase under
programmed I/O control (mode 000 or 001). Hardware provides an automatic control line handshake,
moving data between the FIFO and the ECP port only in the data transfer phase (mode 011 or 010).
If the port is in mode 000 or 001 it may switch to any other mode. If the port is not in mode 000 or 001
it can only be switched into mode 000 or 001. The direction can be changed only in mode 001.
When in extended forward mode, the software should wait for the FIFO to be empty before switching
back to mode 000 or 001. In ECP reverse mode the software waits for all the data to be read from the
FIFO before changing back to mode 000 or 001.
Command/Data
ECP mode allows the transfer of normal 8-bit data or 8-bit commands. In the forward direction,
normal data are transferred when HostAck is high and an 8-bit command is transferred when HostAck
is low. The most significant bits of the command indicate whether it is a run-length count (for
compression) or a channel address.
In the reverse direction, normal data are transferred when PeriphAck is high and an 8-bit command is
transferred when PeriphAck is low. The most significant bit of the command is always zero.
Data Compression
The W83787IF supports run length encoded (RLE) decompression in hardware and can transfer
compressed data to a peripheral. Note that the odd (RLE) compression in hardware is not supported.
In order to transfer data in ECP mode, the compression count is written to the ecpAFifo and the data
byte is written to the ecpDFifo.
相關PDF資料 |
PDF描述 |
|---|---|
| W83791D | W83791D Winbond H/W Monitoring IC |
| W83791SD | H/W MONITORING IC |
| W83791SG | H/W MONITORING IC |
| W83877AF | Multi-Function I/O Port Controller(多功能輸入／輸出口控制器) |
| W83877ATD | enhanced version from Winbonds most popular I/O chip W83877F |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W83787IF | 制造商:WINBOND 制造商全稱:Winbond 功能描述:WINBOND I/O WITH SERIAL-INFRARED SUPPORT |
| W83791D | 制造商:WINBOND 制造商全稱:Winbond 功能描述:Winbond H/W Monitoring IC |
| W83791G | 功能描述:IC MONITOR H/W 48-LQFP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| W83791SD | 制造商:WINBOND 制造商全稱:Winbond 功能描述:H/W MONITORING IC |
| W83791SG | 制造商:WINBOND 制造商全稱:Winbond 功能描述:H/W MONITORING IC |
發布緊急采購，3分鐘左右您將得到回復。