- 您現在的位置：買賣IC網 > PDF目錄363900 > W79E225APG (WINBOND ELECTRONICS CORP) 8-BIT MICROCONTROLLER PDF資料下載
參數資料
| 型號： | W79E225APG |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT MICROCONTROLLER |
| 中文描述： | 8-BIT, FLASH, 40 MHz, MICROCONTROLLER, PQCC44 |
| 封裝： | ROHS COMPLIANT, PLASTIC, LCC-44 |
| 文件頁數： | 91/200頁 |
| 文件大小： | 3644K |
| 代理商： | W79E225APG |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁當前第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁
Preliminary W79E225A/227A Data Sheet
Publication Release Date: December 14, 2007
- 91 -
Revision A2.0
11. INTERRUPTS
The device has a four priority level interrupt structure with 20 interrupt sources. Each of the interrupt
sources has an individual priority bit, flag, interrupt vector and enable bit. In addition, all the interrupts
can be globally enabled or disabled.
11.1 Interrupt Sources
The External Interrupts
INT0
and
INT1
can be either edge triggered or level triggered, depending on
bits IT0 and IT1. The bits IE0 and IE1 in the TCON register are the flags which are checked to
generate the interrupt. In the edge triggered mode, the INTx inputs are sampled in every machine
cycle. If the sample is high in one cycle and low in the next, then a high to low transition is detected
and the interrupts request flag IEx in TCON is set. The flag bit requests the interrupt. Since the
external interrupts are sampled every machine cycle, they have to be held high or low for at least one
complete machine cycle. The IEx flag is automatically cleared when the service routine is called. If the
level triggered mode is selected, then the requesting source has to hold the pin low till the interrupt is
serviced. The IEx flag will not be cleared by the hardware on entering the service routine. If the
interrupt continues to be held low even after the service routine is completed, then the processor may
acknowledge another interrupt request from the same source. Note that the external interrupts INT2
are edge trigger only. By default, the individual interrupt flag corresponding to external interrupt 2 to 5
must be cleared manually by software. It can be configured with hardware cleared by setting the
corresponding bit HCx in T2MOD register. For instance, if HC2 is set hardware will clear IE2 flag after
program enters the interrupt 2 service routine. While for INT3 to INT5 can detect the rising, falling or
both edges which function are selectable by software located in INTCTRL [5:0] register. The Timer 0
and 1 Interrupts are generated by the TF0 and TF1 flags. These flags are set by the overflow in the
Timer 0 and Timer 1. The TF0 and TF1 flags are automatically cleared by the hardware when the
timer interrupt is serviced. The Timer 2 interrupt is generated by a logical OR of the TF2 and the EXF2
flags. These flags are set by overflow or capture/reload events in the timer 2 operation. The hardware
does not clear these flags when a timer 2 interrupt is executed. Software has to resolve the cause of
the interrupt between TF2 and EXF2 and clear the appropriate flag.
When ADC conversion is completed hardware will set flag ADCI to logic high to request ADC interrupt
if bit EADC (IE.6) is in high state. ADCI is cleared by software only.
The I2C function can generate interrupt, if EI2C and EA bits are enabled, when SI Flag is set due to a
new I2C status code is generated, SI flag is generated by hardware and must be cleared by software.
The Watchdog timer can be used as a system monitor or a simple timer. In either case, when the time-
out count is reached, the Watchdog timer interrupt flag WDIF (WDCON.3) is set. If the interrupt is
enabled by the enable bit EIE.4, then an interrupt will occur.
All the bits that generate interrupts can be set or reset by hardware, and thereby software initiated
interrupts can be generated. Each of the individual interrupts can be enabled or disabled by setting or
clearing a bit in the IE SFR. IE also has a global enable/disable bit EA, which can be cleared to
disable all interrupts.
11.2 Priority Level Structure
There are four priority levels for the interrupts; highest, high, low and lowest. The other interrupt
source can be individually set to either high or low levels. Naturally, a higher priority interrupt cannot
be interrupted by a lower priority interrupt. However there exists a predefined hierarchy amongst the
interrupts themselves. This hierarchy comes into play when the interrupt controller has to resolve
simultaneous requests having the same priority level. This hierarchy is defined as shown below; the
interrupts are numbered starting from the highest priority to the lowest.
相關PDF資料 |
PDF描述 |
|---|---|
| W79E227A | 8-BIT MICROCONTROLLER |
| W79E227AFG | 8-BIT MICROCONTROLLER |
| W79E227APG | 8-BIT MICROCONTROLLER |
| W79E532 | 8-BIT MICROCONTROLLER |
| W79E532A40DL | 8-BIT MICROCONTROLLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W79E226AFG | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-bit Microcontroller |
| W79E226ALG | 制造商:Nuvoton Technology Corp 功能描述:IC MCU 32K EPROM FLASH 48LQFP |
| W79E226APG | 制造商:Nuvoton Technology Corp 功能描述:IC MCU 32K EPROM FLASH 44PLCC |
| W79E227A | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-bit Microcontroller |
| W79E227AFG | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-bit Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。