国产精品成人VA在线观看-国产乱妇乱子视频在播放-国产日韩精品一区二区三区在线-国模精品一区二区三区

參數資料
型號: W79E804ASG
廠商: WINBOND ELECTRONICS CORP
元件分類: 微控制器/微處理器
英文描述: 8-BIT MICROCONTROLLER
中文描述: 8-BIT, FLASH, 20 MHz, MICROCONTROLLER, PDSO20
封裝: 0.300 INCH, ROHS COMPLIANT, SOP-20
文件頁數: 98/115頁
文件大小: 1456K
代理商: W79E804ASG
W79E804A/803A/802A
- 98 -
Figure
24-2: I2C Timer Count Block Diagram
24.3 Modes of Operation
The on-chip I2C ports support five operation modes, Master transmitter, Master receiver, Slave
transmitter, Slave receiver, and GC call.
In a given application, I2C port may operate as a master or
as a slave. In the slave mode, the I2C port
hardware looks for its own slave address and the general call address. If one of these addresses is
detected, and if the slave is willing to receive or transmit data from/to master(by setting the AA bit),
acknowledge pulse will be transmitted out on the 9th clock, hence an interrupt is requested on both
master and slave devices if interrupt is enabled. When the microcontroller wishes to become the bus
master, the hardware waits until the bus is free before the master mode is entered so that a possible
slave action is not interrupted. If bus arbitration is lost in the master mode, I2C port switches to the
slave mode immediately and can detect its own slave address in the same serial transfer.
24.3.1 Master Transmitter Mode
Serial data output through SDA while SCL outputs the serial clock. The first byte transmitted contains
the slave address of the receiving device (7 bits) and the data direction bit. In this case the data
direction bit (R/W) will be logic 0, and it is represented by “W” in the flow diagrams. Thus the first byte
transmitted is SLA+W. Serial data is transmitted 8 bits at a time. After each byte is transmitted, an
acknowledge bit is received. START and STOP conditions are output to indicate the beginning and the
end of a serial transfer.
24.3.2 Master Receiver Mode
In this case the data direction bit (R/W) will be logic 1, and it is represented by “R” in the flow
diagrams. Thus the first byte transmitted is SLA+R. Serial data is received via SDA while SCL outputs
the serial clock. Serial data is received 8 bits at a time. After each byte is received, an acknowledge bit
is transmitted. START and STOP conditions are output to indicate the beginning and end of a serial
transfer.
相關PDF資料
PDF描述
W80NF06 N-CHANNEL 60V - 0.0065OHM - 80A TO-220/D2PAK/TO-247 STripFET II POWER MOSFET
W81181AD USB HUB CONTROLLER
W81181D USB HUB CONTROLLER
W81282F-05 USB Keyboard Controller with 4 Ports Hub
W81386-DG Winbond USB Interface MS/SD/MMC Reader
相關代理商/技術參數
參數描述
W79E8213 制造商:未知廠家 制造商全稱:未知廠家 功能描述:W79E8213中文資料
W79E8213_W79E8213R 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Table of contents-
W79E8213AKG 制造商:Nuvoton Technology Corp 功能描述:IC MCU 8BIT 4K FLASH 20DIP
W79E8213ASG 制造商:Nuvoton Technology Corp 功能描述:IC MCU 8BIT 4K FLASH 20SOP
W79E8213RAKG 制造商:Nuvoton Technology Corp 功能描述:IC MCU 8BIT 4K FLASH 20DIP