- 您現在的位置：買賣IC網 > PDF目錄363902 > W83637HF (WINBOND ELECTRONICS CORP) LPC I/O PDF資料下載
參數資料
| 型號： | W83637HF |
| 廠商： | WINBOND ELECTRONICS CORP |
| 英文描述： | LPC I/O |
| 中文描述： | LPC的I / O |
| 文件頁數： | 101/149頁 |
| 文件大小： | 936K |
| 代理商： | W83637HF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁當前第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁
W83637HF
Publication Release Date: June 25, 2003
- 96 -
Revision 1.3
7.10 Power States
W83637HF employs a sophisticated algorithm to partition Smart Card interface's internal circuits to
achieve optimal power utilization. However, users must pay extra care in the design of application
circuits following guidelines stated below to prevent potential signal conflict and unnecessary power
consumption.
There're four power states: disabled state, active state, idle state and power down state. Disabled
state is the default state when power is first applied to the IC. Active state is entered by setting a "1" to
enable bits at bit 0 of CR30 in logical device 0 (refer to Configuration Register section for details). Idle
state means that I/O pins of deselected socket output a predetermined voltage level to disable power
to socket and to prevent leakage from floating connections while Smart Card interface core circuits
might still be servicing other selected socket. SCPWD (Smart Card Power Down, bit 7 of CR22 global
control register) controls whether in active state (SCPWD = 0) or in power down state (SCPWD = 1).
7.11 Disabled State
Smart Card interface is in disabled state initially. Clock is stopped in this state and therefore it is the
least power-consuming state. To prevent current leakage from floating connections, it is designed to
output a predetermined voltage level on all the I/O pins of Smart Card interface as follows:
SCPWR# outputs high to disable power supply to socket;
SCRST#, SCCLK, SCIO, SCC4, SCC8 and SCLED output low;
SCPSNT is tri-stated.
These I/O conditions also apply to both socket A and socket B in power down state (SCPWD = 1) or
deselected socket in idle state. Designers of application circuits must take extra care so that no
contention occurs when Smart Card interface is in those power-saving states. Please refer to
Winbond's recommended application circuit for example.
7.12 Active State
Active state is when Smart Card interface is actually performing all its functions: configuration of control
and interrupt registers, detection of card insertion/extraction, reception of ATR (Answer To Reset)
packet and communication of information between host and card. Refer to section 2.3 for detailed
function description.
Smart Card interface enters active state by setting a "1" to bit 0 of CR30 in logical device 0. This is
the most power-consuming state and actual power consumption is dependent on traffic of interface.
7.13 Idle State
W83637HF supports up to two Smart Card sockets. Only one socket could be active at a time and the
other deselected socket is considered to be in idle state. Selection of active socket is controlled
through socket selection bits which are bits 0 at base address + 3. I/O pins of deselected socket also
output a predetermined voltage level as described in section 2.4.1. Power consumption in this state is
similar to active state because one of the two sockets is selected and core circuit is still functioning.
There is no idle state for W83637HF because only one Smart Card socket is supported and it is always
selected.
相關PDF資料 |
PDF描述 |
|---|---|
| W83637HF-AW | LPC I/O |
| W83697HF | WINBOND I/O |
| W83697 | WINBOND I/O |
| W83697F | WINBOND I/O |
| W83697SF | WINBOND I/O |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W83637HF_06 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:LPC I/O |
| W83637HF-AW | 制造商:WINBOND 制造商全稱:Winbond 功能描述:LPC I/O |
| W83637HG | 制造商:WINBOND 制造商全稱:Winbond 功能描述:LPC I/O |
| W83637HG-AW | 功能描述:IC I/O CONTROLLER 128-QFP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:* 標準包裝:3,000 系列:- 應用:PDA，便攜式音頻/視頻，智能電話 接口:I²C，2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2 |
| W83667HG-B | 制造商:Nuvoton Technology Corp 功能描述:LPC SUPER I/O, PECI 1.1A*, SST 制造商:Nuvoton Technology 功能描述:LPC SUPER I/O, PECI 1.1A*, SST |
發布緊急采購，3分鐘左右您將得到回復。