国产精品成人VA在线观看-国产乱妇乱子视频在播放-国产日韩精品一区二区三区在线-国模精品一区二区三区

參數資料
型號： W83697HF
廠商： WINBOND ELECTRONICS CORP
元件分類： 外設及接口
英文描述： WINBOND I/O
中文描述： MULTIFUNCTION PERIPHERAL, PQFP128
封裝： PLASTIC, QFP-128
文件頁數： 29/167頁
文件大小： 1094K
代理商： W83697HF
W83697HF/F
Publication Release Date: Feb. 2002
- 20 - Revision 0.70
At the start of a command the FIFO is always disabled and command parameters must be sent based
upon the RQM and DIO bit settings in the main status register. When the FDC enters the command
execution phase, it clears the FIFO of any data to ensure that invalid data are not transferred.
An overrun and underrun will terminate the current command and the data transfer. Disk writes will
complete the current sector by generating a 00 pattern and valid CRC. Reads require the host to remove
the remaining data so that the result phase may be entered.
DMA transfers are enabled with the SPECIFY command and are initiated by the FDC by activating the
DRQ pin during a data transfer command. The FIFO is enabled directly by asserting DACK# and
addresses need not be valid.
Note that if the DMA controller is programmed to function in verify mode a pseudo read is performed by
the FDC based only on DACK#. This mode is only available when the FDC has been configured into byte
mode (FIFO disabled) and is programmed to do a read. With the FIFO enabled the above operation is
performed by using the new VERIFY command. No DMA operation is needed.@
3.1.3
Data Separator
The function of the data separator is to lock onto the incoming serial read data. When a lock is achieved
the serial front end logic of the chip is provided with a clock which is synchronized to the read data. The
synchronized clock, called the Data Window, is used to internally sample the serial data portion of the
bit cell, and the alternate state samples the clock portion. Serial to parallel conversion logic separates
the read data into clock and data bytes.
The Digital Data Separator (DDS) has three parts: control logic, error adjustment, and speed tracking.
The DDS circuit cycles once every 12 clock cycles ideally. Any data pulse input will be synchronized
and then adjusted by immediate error adjustment. The control logic will generate RDD and RWD for
every pulse input. During any cycle where no data pulse is present, the DDS cycles are based on speed.
A digital integrator is used to keep track of the speed changes in the input data stream.
3.1.4
Write Precompensation
The write precompensation logic is used to minimize bit shifts in the RDDATA stream from the disk
drive. Shifting of bits is a known phenomenon in magnetic media and is dependent on the disk media
and the floppy drive.
The FDC monitors the bit stream that is being sent to the drive. The data patterns that require
precompensation are well known. Depending upon the pattern, the bit is shifted either early or late
relative to the surrounding bits.
相關PDF資料
PDF描述
W83697 WINBOND I/O
W83697F WINBOND I/O
W83697SF WINBOND I/O
W83757 SUPER I/O CHIP
W83759 ADVANCED VL-IDE DISK CONTROLLER
相關代理商/技術參數
參數描述
W83697HF_05 制造商:WINBOND 制造商全稱:Winbond 功能描述:LPC I/O
W83697HG 功能描述:IC LPC SUPER I/O 128-PQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA，便攜式音頻/視頻，智能電話 接口:I²C，2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2
W83697SF 制造商:WINBOND 制造商全稱:Winbond 功能描述:WINBOND I/O
W83697UF 制造商:WINBOND 制造商全稱:Winbond 功能描述:LPC I/O
W83697UG 功能描述:IC LPC SUPER I/O 128-PQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA，便攜式音頻/視頻，智能電話 接口:I²C，2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*