国产精品成人VA在线观看-国产乱妇乱子视频在播放-国产日韩精品一区二区三区在线-国模精品一区二区三区

參數資料
型號: W79E227A
廠商: WINBOND ELECTRONICS CORP
元件分類: 8位微控制器
英文描述: 8-BIT MICROCONTROLLER
中文描述: 8位微控制器
文件頁數: 148/200頁
文件大小: 3644K
代理商: W79E227A
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁當前第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁
Preliminary W79E225A/227A Data Sheet
Publication Release Date: December 14, 2007
- 148 -
Revision A2.0
ENS
I2C serial function block enable bit. When ENS=1 the I2C serial function enables. The
port latches of SDA1 and SCL1 must be set to logic high.
I2C START Flag. Setting STA to logic 1 to enter master mode, the I2C hardware sends a
START or repeat START condition to bus when the bus is free.
I2C STOP Flag. In master mode, setting STO to transmit a STOP condition to bus then
I2C hardware will check the bus condition if a STOP condition is detected this flag will be
cleared by hardware automatically. In a slave mode, setting STO resets I2C hardware to
the “not addressed slave mode”.
I2C Port 1 Interrupt Flag. When a new SIO state is present in the S1STA register, the SI
flag is set by hardware, and if the EA and EI2C1 bits are both set, the I2C1 interrupt is
requested. SI must be cleared by software.
Assert Acknowledge control bit. When AA=1 prior to address or data received, an
acknowledged (low level to SDA) will be returned during the acknowledge clock pulse on
the SCL line when; 1.) A slave is acknowledging the address sent from master, 2.) The
receiver devices are acknowledging the data sent by transmitter. When AA=0 prior to
address or data received, a not acknowledged (high level to SDA) will be returned during
the acknowledge clock pulse on the SCL line.
By default it is zero and input are allows to come in through SDA pin. As when it is 1 input
is disallow and to prevent leakage current. During Power-Down mode input is disallow.
STA
STO
SI
AA
I2CIN
17.2.4 Status Register, I2STATUS
I2STATUS is an 8-bit read-only register. The three least significant bits are always 0. The five most
significant bits contain the status code. There are 23 possible status codes. When I2STATUS contains
F8H, no serial interrupt is requested. All other I2STATUS values correspond to defined I2C ports
states. When each of these states is entered, a status interrupt is requested (SI = 1). A valid status
code is present in I2STATUS one machine cycle after SI is set by hardware and is still present one
machine cycle after SI has been reset by software.
In addition, state 00H stands for a Bus Error. A Bus Error occurs when a START or STOP condition is
present at an illegal position in the format frame. Examples of illegal positions are during the serial
transfer of an address byte, a data byte or an acknowledge bit.
17.2.5 I2C Clock Baud Rate Control, I2CLK
The data baud rate of I2C is determines by I2CLK register when I2C port is in a master mode. It is not
important when I2C port is in a slave mode. In the slave modes, SIO will automatically synchronize
with any clock frequency up to 400 KHz from master I2C device.
The data baud rate of I2C setting conforms to the following equation.
Data Baud Rate of I2C = F
CPU
/ (I2CLK + 1), where F
CPU
= F
OSC
/4.
For example, if F
OSC
=16MHz, the I2CLK=40(28H), the data baud rate of I2C = (16MHz/4)/(40+1) =
97.56K bits/sec.
17.2.6 I2C Time-out Counter, I2Timer
In W79E225/227, the I2C logic block provides a 14-bit timer-out counter that helps user to deal with
bus pending problem. When SI is cleared user can set ENTI=1 to start the time-out counter. If I2C bus
is pended too long to get any valid signal from devices on bus, the time-out counter overflows cause
TIF=1 to request an I2C interrupt. The I2C interrupt is requested in the condition of either SI=1 or
TIF=1. Flags SI and TIF must be cleared by software.
相關PDF資料
PDF描述
W79E227AFG 8-BIT MICROCONTROLLER
W79E227APG 8-BIT MICROCONTROLLER
W79E532 8-BIT MICROCONTROLLER
W79E532A40DL 8-BIT MICROCONTROLLER
W79E532A40DN 8-BIT MICROCONTROLLER
相關代理商/技術參數
參數描述
W79E227AFG 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-bit Microcontroller
W79E227ALG 制造商:Nuvoton Technology Corp 功能描述:IC MCU 64K EPROM FLASH 48LQFP
W79E227APG 制造商:Nuvoton Technology Corp 功能描述:IC MCU 64K EPROM FLASH 44PLCC
W79E342 制造商:WINBOND 制造商全稱:Winbond 功能描述:W79E342 datasheet
W79E4051_2051 制造商:WINBOND 制造商全稱:Winbond 功能描述:W79E4051_2051_SC7(中文)