国产精品成人VA在线观看-国产乱妇乱子视频在播放-国产日韩精品一区二区三区在线-国模精品一区二区三区

參數資料
型號: W83877TF
廠商: WINBOND ELECTRONICS CORP
元件分類: 外設及接口
英文描述: Multi-Function I/O Port Controller(用于個人計算機的多功能輸入/輸出口控制器)
中文描述: MULTIFUNCTION PERIPHERAL, PQFP100
封裝: QFP-100
文件頁數: 59/154頁
文件大小: 821K
代理商: W83877TF
W83877TF
Publication Release Date: March 1998
- 55 -
Version 0.61
A watchdog timer is required to prevent system lockup. The timer indicates that more than 10
μ
S
have elapsed from the start
of the EPP
cycle to the time
WAIT
is de-asserted. The current EPP cycle
is aborted when a time-out occurs. The time-out condition is indicated in Status bit 0.
EPP Operation
The EPP operates on a two-phase cycle. First, the host selects the register within the device for
subsequent operations. Second, the host performs a series of read and/or write byte operations to the
selected register. Four operations are supported on the EPP: Address Write, Data Write, Address
Read, and Data Read. All operations on the EPP device are performed synchronously.
EPP Version 1.9 Operation
The EPP read/write operation can be completed under the following conditions:
a. If the nWait is active low, when the read cycle (nWrite inactive high, nDStrb/nAStrb active low) or
write cycle (nWrite active low, nDStrb/nAStrb active low) starts, the read/write cycle proceeds
normally and will be completed when nWait goes inactive high.
b. If nWait is inactive high, the read/write cycle will not start. It must wait until nWait changes to
active low, at which time it will start as described above.
EPP Version 1.7 Operation
The EPP read/write cycle can start without checking whether nWait is active or inactive. Once the
read/write cycle starts, however, it will not terminate until nWait changes from active low to inactive
high.
4.3 Extended Capabilities Parallel (ECP) Port
This
port is software and hardware compatible with existing parallel ports, so it may be used as a
standard printer mode if ECP is not required. It provides an automatic high burst-bandwidth channel
that supports DMA for ECP in both the forward (host to peripheral) and reverse (peripheral to host)
directions.
Small FIFOs are used in both forward and reverse directions to improve the maximum bandwidth
requirement. The size of the FIFO is 16 bytes. The ECP port supports an automatic handshake for
the standard parallel port to improve compatibility mode transfer speed.
The ECP port supports run-length-encoded (RLE) decompression (required) in the hardware.
Compression is accomplished by counting identical bytes and transmitting an RLE byte that indicates
how many times the next byte is to be repeated. The hardware support for compression is optional.
For more information about the ECP Protocol, refer to the Extended Capabilities Port Protocol and
ISA Interface Standard.
相關PDF資料
PDF描述
W83971D AC97 AUDIO CODEC
W83977AF PLUG & PLAY 1.0A COMPLIANT
W83977EF WINBOND I/O
W83977F PLUG & PLAY 1.0A COMPLIANT
W83977TF-AW I/O chip disk drive adapter
相關代理商/技術參數
參數描述
W83877TG 功能描述:IC I/O CONTROLLER 100-PQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA,便攜式音頻/視頻,智能電話 接口:I²C,2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤(4x4) 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2
W83910F 制造商:未知廠家 制造商全稱:未知廠家 功能描述:IPMI BMC plus H/W Monitor. UART. 5-sets Master/Slave SMBus. for Server PC Application
W83960G (REV. B) 制造商:Nuvoton Technology Corp 功能描述:IC H/W MONITOR 64LQFP
W83971D 制造商:WINBOND 制造商全稱:Winbond 功能描述:AC97 AUDIO CODEC
W83977A 制造商:WINBOND 制造商全稱:Winbond 功能描述:WINBOND I/O