国产精品成人VA在线观看-国产乱妇乱子视频在播放-国产日韩精品一区二区三区在线-国模精品一区二区三区

參數資料
型號： W83877TF
廠商： WINBOND ELECTRONICS CORP
元件分類： 外設及接口
英文描述： Multi-Function I/O Port Controller(用于個人計算機的多功能輸入/輸出口控制器)
中文描述： MULTIFUNCTION PERIPHERAL, PQFP100
封裝： QFP-100
文件頁數： 67/154頁
文件大小： 821K
代理商： W83877TF
W83877TF
Publication Release Date: March 1998
- 63 -
Version 0.61
4.3.13 ECP Operation
The host must negotiate on the parallel port to determine if the peripheral supports the ECP protocol
before ECP operation. After negotiation, it is necessary to initialize some of the port bits. The
following are required:
(a) Set direction = 0, enabling the drivers.
(b) Set strobe = 0, causing the nStrobe signal to default to the deasserted state.
(c) Set autoFd = 0, causing the nAutoFd signal to default to the deasserted state.
(d) Set mode = 011 (ECP Mode)
ECP address/RLE bytes or data bytes may be sent automatically by writing the ecpAFifo or ecpDFifo,
respectively.
Mode Switching
Software will execute P1284 negotiation and all operations prior to a data transfer phase under
programmed I/O control (mode 000 or 001). Hardware provides an automatic control line handshake,
moving data between the FIFO and the ECP port only in the data transfer phase (mode 011 or 010).
If the port is in mode 000 or 001 it may switch to any other mode. If the port is not in mode 000 or 001
it can only be switched into mode 000 or 001. The direction can be changed only in mode 001.
When in extended forward mode, the software should wait for the FIFO to be empty before switching
back to mode 000 or 001. In ECP reverse mode the software waits for all the data to be read from the
FIFO before changing back to mode 000 or 001.
Command/Data
ECP mode allows the transfer of normal 8-bit data or 8-bit commands. In the forward direction,
normal data are transferred when HostAck is high and an 8-bit command is transferred when HostAck
is low. The most significant bits of the command indicate whether it is a run-length count (for
compression) or a channel address.
In the reverse direction, normal data are transferred when PeriphAck is high and an 8-bit command is
transferred when PeriphAck is low. The most significant bit of the command is always zero.
Data Compression
The W83877TF supports run length encoded (RLE) decompression in hardware and can transfer
compressed data to a peripheral. Note that the odd (RLE) compression in hardware is not supported.
In order to transfer data in ECP mode, the compression count is written to the ecpAFifo and the data
byte is written to the ecpDFifo.
4.3.14 FIFO Operation
The FIFO threshold is set in configuration register 5. All data transfers to or from the parallel port can
proceed in DMA or Programmed I/O (non-DMA) mode, as indicated by the selected mode. The FIFO
is used by selecting the Parallel Port FIFO mode or ECP Parallel Port Mode. After a reset, the FIFO
is disabled.
相關PDF資料
PDF描述
W83971D AC97 AUDIO CODEC
W83977AF PLUG & PLAY 1.0A COMPLIANT
W83977EF WINBOND I/O
W83977F PLUG & PLAY 1.0A COMPLIANT
W83977TF-AW I/O chip disk drive adapter
相關代理商/技術參數
參數描述
W83877TG 功能描述:IC I/O CONTROLLER 100-PQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA，便攜式音頻/視頻，智能電話 接口:I²C，2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2
W83910F 制造商:未知廠家 制造商全稱:未知廠家 功能描述:IPMI BMC plus H/W Monitor. UART. 5-sets Master/Slave SMBus. for Server PC Application
W83960G (REV. B) 制造商:Nuvoton Technology Corp 功能描述:IC H/W MONITOR 64LQFP
W83971D 制造商:WINBOND 制造商全稱:Winbond 功能描述:AC97 AUDIO CODEC
W83977A 制造商:WINBOND 制造商全稱:Winbond 功能描述:WINBOND I/O
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*