- 您現在的位置：買賣IC網 > PDF目錄363894 > W742C81A (WINBOND ELECTRONICS CORP) 4-BIT MICROCONTROLLER PDF資料下載
參數資料
| 型號： | W742C81A |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 4-BIT MICROCONTROLLER |
| 中文描述： | 4-BIT, FLASH, MICROCONTROLLER, UUC100 |
| 封裝： | DIE-100 |
| 文件頁數： | 22/45頁 |
| 文件大小： | 567K |
| 代理商： | W742C81A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁
Preliminary W742E81A/W742C81A
- 22 -
6.15.1 Hold Mode Release Enable Flag (HEF)
The hold mode release enable flag is organized as an 8-bit binary register (HEF.0 to HEF.7). The
HEF is used to control the hold mode release conditions. It is controlled by the MOV HEF, #I
instruction. The bit descriptions are as follows:
Note: W means write only.
HEF.0 = 1 Overflow from the Divider 0 causes Hold mode to be released.
HEF.1 = 1 Underflow from Timer 0 causes Hold mode to be released.
HEF.2 = 1 Signal change at port RC causes Hold mode to be released.
HEF.3, HEF.5 & HEF.6 are reserved.
HEF.4 = 1 Overflow from the Divider 1 causes Hold mode to be released.
HEF.7 = 1 Underflow from Timer 1 causes Hold mode to be released.
w
0
1
2
HEF
w
w
w
w
3
4
5
6
7
6.15.2 Interrupt Enable Flag (IEF)
The interrupt enable flag is organized as a 8-bit binary register (IEF.0 to IEF.7). These bits are used
to control the interrupt conditions. It is controlled by the MOV IEF, #I instruction. When one of these
interrupts is accepted, the corresponding to the bit of the event flag will be reset, but the other bits are
unaffected. In interrupt subroutine, these interrupts will be disable till the instruction MOV IEF, #I
or
EN INT
is executed again. Otherwise, these interrupts can be disable by executing DIS INT
instruction. The bit descriptions are as follows:
Note: W means write only.
IEF.0 = 1 Interrupt 0 is accepted by overflow from the Divider 0.
IEF.1 = 1 Interrupt 1 is accepted by underflow from the Timer 0.
IEF.2 = 1 Interrupt 2 is accepted by a signal change at port RC.
IEF.3, IEF.5 & IEF.6 are reserved.
IEF.4 = 1 Interrupt 4 is accepted by overflow from the Divider 1.
IEF.7 = 1 Interrupt 7 is accepted by underflow from Timer 1.
w
1
2
3
IEF
4
w
w
5
6
0
w
w
7
6.15.3 Port Enable Flag (PEF)
The port enable flag is organized as 4-bit binary register (PEF.0 to PEF.3). Before port RC may be
used to release the hold mode or preform interrupt function, the content of the PEF must be set first.
The PEF is controlled by the MOV PEF, #I instruction. The bit descriptions are as follows:
相關PDF資料 |
PDF描述 |
|---|---|
| W742S819 | 4-BIT TELEPHONE CONTROLLER |
| W742S81A | 4-BIT SINGLE-CHIP MICROCONTROLLER FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROL TRANSMITTER |
| W742S82A | 4-BIT TELEPHONE CONTROLLER |
| W74IE20X | 4-BIT FLASH MICROCONTROLLER |
| W741E202 | 4-BIT FLASH MICROCONTROLLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W742CE811 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:4-BIT MICROCONTROLLER |
| W742E | 制造商:WINBOND 制造商全稱:Winbond 功能描述:4 BIT MICROCONTROLLER |
| W742E/C811 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:4 BIT MICROCONTROLLER |
| W742E811 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| W742E813 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:4-BIT MICROCONTROLLER |
發布緊急采購，3分鐘左右您將得到回復。