- 您現在的位置：買賣IC網 > PDF目錄363894 > W742C81A (WINBOND ELECTRONICS CORP) 4-BIT MICROCONTROLLER PDF資料下載
參數資料
| 型號： | W742C81A |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 4-BIT MICROCONTROLLER |
| 中文描述： | 4-BIT, FLASH, MICROCONTROLLER, UUC100 |
| 封裝： | DIE-100 |
| 文件頁數： | 26/45頁 |
| 文件大小： | 567K |
| 代理商： | W742C81A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁
Preliminary W742E81A/W742C81A
- 26 -
determine the structure of the input/output ports; it is controlled by the MOV PM0, #I instruction. The
bit descriptions are as follows:
PM0
Note: W means write only.
w
w
w
0
1
2
w
3
Bit 0 = 0 RA port is CMOS output type.
Bit 1 = 0 RB port is CMOS output type.
Bit 2 = 0 RC port pull-high resistor is disabled. Bit 2 = 1 RC port pull-high resistor is enabled.
Bit 3 is reserved.
Bit 0 = 1 RA port is NMOS open drain output type.
Bit 1 = 1 RB port is NMOS open drain output type.
6.17.2 Port Mode 1 Register (PM1)
The port mode 1 register is organized as 4-bit binary register (PM1.0 to PM1.3). PM1 can be used to
control the input/output mode of port RA. PM1 is controlled by the MOV PM1, #I instruction. The bit
descriptions are as follows:
PM1
Note: W means write only.
w
w
w
0
1
2
w
3
Bit 0 = 0 RA.0 works as output pin; Bit 0 = 1 RA.0 works as input pin
Bit 1 = 0 RA.1 works as output pin; Bit 1 = 1 RA.1 works as input pin
Bit 2 = 0 RA.2 works as output pin; Bit 2 = 1 RA.2 works as input pin
Bit 3 = 0 RA.3 works as output pin; Bit 3 = 1 RA.3 works as input pin
At initial reset, port RA is input mode (PM1 = 1111B).
6.17.3 Port Mode 2 Register (PM2)
The port mode 2 register is organized as 4-bit binary register (PM2.0 to PM2.3). PM2 can be used to
control the input/output mode of port RB. PM2 is controlled by the MOV PM2, #I instruction. The bit
descriptions are as follows:
PM2
Note: W means write only.
w
w
w
0
1
2
w
3
Bit 0 = 0 RB.0 works as output pin; Bit 0 = 1 RB.0 works as input pin
Bit 1 = 0 RB.1 works as output pin; Bit 1 = 1 RB.1 works as input pin
Bit 2 = 0 RB.2 works as output pin; Bit 2 = 1 RB.2 works as input pin
Bit 3 = 0 RB.3 works as output pin; Bit 3 = 1 RB.3 works as input pin
At initial reset, the port RB is input mode (PM2 = 1111B).
相關PDF資料 |
PDF描述 |
|---|---|
| W742S819 | 4-BIT TELEPHONE CONTROLLER |
| W742S81A | 4-BIT SINGLE-CHIP MICROCONTROLLER FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROL TRANSMITTER |
| W742S82A | 4-BIT TELEPHONE CONTROLLER |
| W74IE20X | 4-BIT FLASH MICROCONTROLLER |
| W741E202 | 4-BIT FLASH MICROCONTROLLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W742CE811 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:4-BIT MICROCONTROLLER |
| W742E | 制造商:WINBOND 制造商全稱:Winbond 功能描述:4 BIT MICROCONTROLLER |
| W742E/C811 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:4 BIT MICROCONTROLLER |
| W742E811 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| W742E813 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:4-BIT MICROCONTROLLER |
發布緊急采購，3分鐘左右您將得到回復。