- 您現在的位置：買賣IC網 > PDF目錄363894 > W742C810 (WINBOND ELECTRONICS CORP) 4-BIT MICROCONTROLLER PDF資料下載
參數資料
| 型號： | W742C810 |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 4-BIT MICROCONTROLLER |
| 中文描述： | 4-BIT, MROM, 3.58 MHz, MICROCONTROLLER, PQFP100 |
| 封裝： | 14 X 20 MM, 2.75 MM HEIGHT, QFP-100 |
| 文件頁數： | 25/42頁 |
| 文件大小： | 501K |
| 代理商： | W742C810 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁
Preliminary W742C810
Publication Release Date: May 1999
- 25 -
Revision A1
6.17.3 Port Mode 2 Register (PM2)
The port mode 2 register is organized as a 4-bit binary register (PM2.0 to PM2.3). PM2 can be used
to control the input/output mode of port RB. PM2 is controlled by the MOV PM2, #I instruction. The bit
descriptions are as follows:
PM2
w
w
w
0
1
2
w
3
Note: W means write only.
Bit 0 = 0 RB.0 works as output pin; Bit 0 = 1 RB.0 works as input pin
Bit 1 = 0 RB.1 works as output pin; Bit 1 = 1 RB.1 works as input pin
Bit 2 = 0 RB.2 works as output pin; Bit 2 = 1 RB.2 works as input pin
Bit 3 = 0 RB.3 works as output pin; Bit 3 = 1 RB.3 works as input pin
At initial reset, the port RB is input mode (PM2 = 1111B).
6.17.4 Port Mode 5 Register (PM5)
The port mode 5 register is organized as a 4-bit binary register (PM5.0 to PM5.3). PM5 can be used
to control the input/output mode of port RD. PM5 is controlled by the MOV PM5, #I instruction. The bit
descriptions are as follows:
PM5
Note: W means write only.
w
w
w
0
1
2
w
3
Bit 0 = 0 RD.0 works as output pin; Bit 0 = 1 RD.0 works as input pin
Bit 1 = 0 RD.1 works as output pin; Bit 1 = 1 RD.1 works as input pin
Bit 2 = 0 RD.2 works as output pin; Bit 2 = 1 RD.2 works as input pin
Bit 3 = 0 RD.3 works as output pin; Bit 3 = 1 RD.3 works as input pin
At initial reset, the port RD is input mode (PM5 = 1111B).
6.18 Input Ports RC
Port RC consists of pins RC.0 to RC.3. Each pin of port RC can be connected to a pull-up resistor,
which is controlled by the port mode 0 register(PM0). When the PEF, HEF, and IEF corresponding to
the RC port are set, a signal change at the specified pins of port RC will execute the hold mode
release or interrupt subroutine. Port status register 0 (PSR0) records the status of ports RC, i.e., any
signal changes on the pins that make up the ports. PSR0 can be read out and cleared by the MOV R,
PSR0, and CLR PSR0 instructions. In addition, the falling edge signal on the pin of port RC specified
by the instruction MOV SEF, #I will cause the device to exit the stop mode. Refer to Figure 6-12 and
the instruction table for more details.
相關PDF資料 |
PDF描述 |
|---|---|
| W742C813 | 4-BIT SINGLE-CHIP MICROCONTROLLER FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROL TRANSMITTER |
| W742C814 | 4-BIT SINGLE-CHIP MICROCONTROLLER FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROL TRANSMITTER |
| W742E813 | 4-BIT MICROCONTROLLER |
| W742C81A | 4-BIT MICROCONTROLLER |
| W742S819 | 4-BIT TELEPHONE CONTROLLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W742C811 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:4-BIT MICROCONTROLLER |
| W742C813 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:4 BIT MICROCONTROLLER |
| W742C814 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:4 BIT MICROCONTROLLER |
| W742C816 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| W742C818 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。