- 您現在的位置：買賣IC網 > PDF目錄363901 > W79E648 (WINBOND ELECTRONICS CORP) Fast 8051 Compatible microcontroller with a redesigned Processor PDF資料下載
參數資料
| 型號： | W79E648 |
| 廠商： | WINBOND ELECTRONICS CORP |
| 英文描述： | Fast 8051 Compatible microcontroller with a redesigned Processor |
| 中文描述： | 快速8051兼容微控制器重新設計的處理器 |
| 文件頁數： | 35/80頁 |
| 文件大小： | 407K |
| 代理商： | W79E648 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁當前第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁
Preliminary W79E648
Publication Release Date: 05/31/2004
- 35 - Revision A1
Table 5. Status of external pins during Idle and Power Down
Mode
Program
Memory
Internal
External
Internal
External
ALE
PSEN
PORT0
PORT1
PORT2
PORT3
Idle
Idle
Power Down
Power Down
1
1
0
0
1
1
0
0
Data
Float
Data
Float
Data
Data
Data
Data
Data
Address
Data
Data
Data
Data
Data
Data
Reset Conditions
The user has several hardware related options for placing the W79E648 into reset condition. In
general, most register bits go to their reset value irrespective of the reset condition, but there are a few
flags whose state depends on the source of reset. The user can use these flags to determine the
cause of reset using software. There are two ways of putting the device into reset state. They are
External reset and Watchdog reset.
External Reset
The device continuously samples the RST pin at state C4 of every machine cycle. Therefore the RST
pin must be held for at least 2 machine cycles to ensure detection of a valid RST high. The reset
circuitry then synchronously applies the internal reset signal. Thus the reset is a synchronous
operation and requires the clock to be running to cause an external reset.
Once the device is in reset condition, it will remain so as long as RST is 1. Even after RST is
deactivated, the device will continue to be in reset state for up to two machine cycles, and then begin
program execution from 0000h. There is no flag associated with the external reset condition. However
since the other two reset sources have flags, the external reset can be considered as the default reset
if those two flags are cleared.
The software must clear the POR flag after reading it, otherwise it will not be possible to correctly
determine future reset sources. If the power fails, i.e. falls below Vrst, then the device will once again
go into reset state. When the power returns to the proper operating levels, the device will again
perform a power on reset delay and set the POR flag.
Watchdog Timer Reset
The Watchdog timer is a free running timer with programmable time-out intervals. The user can clear
the watchdog timer at any time, causing it to restart the count. When the time-out interval is reached
an interrupt flag is set. If the Watchdog reset is enabled and the watchdog timer is not cleared, then
512 clocks from the flag being set, the watchdog timer will generate a reset . This places the device
into the reset condition. The reset condition is maintained by hardware for two machine cycles. Once
the reset is removed the device will begin execution from 0000h.
相關PDF資料 |
PDF描述 |
|---|---|
| W79E802 | 8-BIT MICROCONTROLLER |
| W79E802A | 8-BIT MICROCONTROLLER |
| W79E802ADG | 8-BIT MICROCONTROLLER |
| W79E802ASG | 8-BIT MICROCONTROLLER |
| W79E803 | 8-BIT MICROCONTROLLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W79E658A40FL | 制造商:Nuvoton Technology Corp 功能描述:IC MCU 8BIT 100QFP |
| W79E659A40FL | 制造商:Nuvoton Technology Corp 功能描述:IC MCU 8BIT 100QFP |
| W79E802 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-BIT MICROCONTROLLER |
| W79E802A | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-BIT MICROCONTROLLER |
| W79E802ADG | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-BIT MICROCONTROLLER |
發布緊急采購，3分鐘左右您將得到回復。