- 您現在的位置：買賣IC網 > PDF目錄363893 > W66910CD (WINBOND ELECTRONICS CORP) TE Mode ISDN S/T-Controller with Microprocessor Interface PDF資料下載
參數資料
| 型號： | W66910CD |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | 通信及網絡 |
| 英文描述： | TE Mode ISDN S/T-Controller with Microprocessor Interface |
| 中文描述： | SPECIALTY TELECOM CIRCUIT, PQFP100 |
| 封裝： | 14 X 20 MM, 1.40 MM HEIGHT, QFP-100 |
| 文件頁數： | 21/81頁 |
| 文件大小： | 681K |
| 代理商： | W66910CD |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁
Data Sheet
W66910 PCI ISDN S/T-Controller
Publication Release Date:
Feb,2001
Revision 1.0
-21 -
This state is identical to "F3 Deactivated without clock" except the internal clocks are enabled. The state is entered by the ECK
command. The clocks are enabled approximately 0.5 ms to 4 ms after the ECK command, depending on the crystal capacitances.
(It is about 0.5 ms for 12pF to 33pF capacitance).
F3 Awaiting Deactivation
The W66910 enters this state after receiving INFO 0 (in states F5 to F8) for 16ms (64 frames). This time constant prevents
spurious effect on S interface. Any non-INFO 0 signal on the S interface causes transition to "F5 Identifying Input" state. If this
transition does not occur in a specific time (500 - 1000 ms), the microprocessor may issue DRC or ECK command to deactivate
layer 1.
F4 Awaiting Signal
This state is reached when an activate request command has been received. In this state, the layer 1 transmits INFO1 and INFO 0
is received from the S interface. The software starts timer T3 of I.430 when issuing activate request command. The software
deactivates layer 1 if no signal other than INFO 0 has been received on S interface before expiration of T3.
F5 Identifying Input
After the receipt of any non-INFO 0 signal from NT, the W66910 ceases to transmit INFO 1 and awaits identification of INFO 2
or INFO 4. This state is reached at most 50
μ
s after a signal different from INFO 0 is present at the receiver of the S interface.
F6 Synchronized
When W66910 receives an activation signal (INFO 2), it responds with INFO 3 and waits for normal frames (INFO 4). This state
is reached at most 6 ms after an INFO 2 arrives at the S interface (in case the clocks were disabled in "F3 Deactivated without
clock").
F7 Activated
This is the normal active state with the layer 1 protocol activated in both directions. From state "F6 Synchronized" , state F7 is
reached at most 0.5 ms after reception of INFO 4. From state "F3 Deactivated without clock" with the clocks disabled, state F7 is
reached at most 6 ms after the W66910 is directly activated by INFO 4.
F8 Lost Framing
This is the state where the W66910 has lost frame synchronization and is awaiting resynchronization by INFO 2 or INFO 4 or
deactivation by INFO 0.
Special States:
Analog Loop Initiated
On Enable Analog Loop command, INFO 3 is sent by the line transmitter internally to the line receiver (INFO 0 is sent to the
line). The receiver is not yet synchronized.
Analog Loop Activated
The receiver is synchronized on INFO 3 which is looped back internally from the transmitter. The indication 'TI" or "ATI" is sent
depending on whether or not a signal different from INFO 0 is detected on the S interface.
Send Continuous Pulses
A 96 kHz continuous pulse with alternating polarities is sent.
相關PDF資料 |
PDF描述 |
|---|---|
| W6691 | ISDN S/T Interface Transceiver |
| W6691CD | ISDN S/T Interface Transceiver |
| W6691CP | ISDN S/T Interface Transceiver |
| W6692 | PCI Bus ISDN S/T Interface Controller(PCI總線的ISDN S/T接口控制器) |
| W6693A | USB Bus ISDN S/T Interface Controller(USB總線的ISDN S/T接口控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W6691CD | 制造商:WINBOND 制造商全稱:Winbond 功能描述:ISDN S/T Interface Transceiver |
| W6691CP | 制造商:WINBOND 制造商全稱:Winbond 功能描述:ISDN S/T Interface Transceiver |
| W6692 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:PCI Bus ISDN S/T-Controller |
| W6692A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:TE Mode S/T Controller with PCI 2.2 Interface and ACPT |
| W6692ACD | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:ISDN LINE INTERFACE|BASIC|CMOS|QFP|100PIN|PLASTIC |
發布緊急采購，3分鐘左右您將得到回復。