- 您現在的位置：買賣IC網 > PDF目錄363893 > W66910CD (WINBOND ELECTRONICS CORP) TE Mode ISDN S/T-Controller with Microprocessor Interface PDF資料下載
參數資料
| 型號： | W66910CD |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | 通信及網絡 |
| 英文描述： | TE Mode ISDN S/T-Controller with Microprocessor Interface |
| 中文描述： | SPECIALTY TELECOM CIRCUIT, PQFP100 |
| 封裝： | 14 X 20 MM, 1.40 MM HEIGHT, QFP-100 |
| 文件頁數： | 30/81頁 |
| 文件大小： | 681K |
| 代理商： | W66910CD |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁
Data Sheet
W66910 PCI ISDN S/T-Controller
Publication Release Date:
Feb,2001
Revision 1.0
-30 -
-
Digital loop
via DLP bit in D_MODE register: In the layer 2 block, the transmitted 2B+D data are internally
looped (from HDLC transmitter to HDLC receiver), and in the PCM ports, the transmitted B channels are
internally looped (from PCM inputs to PCM outputs). The clock timings are generated internally and are
independent of the S bus timing. This loop function is used for test of PCM and higher layer functions, excluding
layer 1. After hardware reset, W66910 will power down if S bus is not connected or if there is no signal on the S
bus. In this case, the C/I command ECK must be issued to power up the chip.
-
Analog loop
via the C/I command EAL: The analog S interface transmitter is internally connected to the S
interface receiver. When the receiver has synchronized itself to the internal INFO 3 signal, the message "Test
Indication" or "Awake Test Indication" is delivered to the CIR register. No signal is transmitted over the S
interface.
In this mode, the S interface awake detector is enabled. Therefore if a level (INFO 2/ INFO 4) is detected on the S
interface, this will be reported by the "Awake Test Indication (ATI)" indication.
-
Remote loopback
via RLP bit in D_MODE register: The digital 2B data received from the S interface receiver is
loopbacked to the S interface transmitter. The D channel is not looped. When RLP is enabled, layer 1 D channel is
connected to HDLC port and DLP cannot be enabled.
- Transmission of special test signals via layer 1 command:
*
Send Single Pulses
(SSP): To send isolated single pulses of alternating polarity, with pulse width of one bit time,
250 us apart, with a repetition frequency of 2 kHz.
*
Send Continuous Pulses
(SCP): To send continuous pulses of alternating polarity, with pulse width of bit time.
The repetition frequency is 96 kHz.
FIG.7.7 SSP AND SCP TEST SIGNALS
250 us
(a) Single pulses
(b) Continuous pulses
相關PDF資料 |
PDF描述 |
|---|---|
| W6691 | ISDN S/T Interface Transceiver |
| W6691CD | ISDN S/T Interface Transceiver |
| W6691CP | ISDN S/T Interface Transceiver |
| W6692 | PCI Bus ISDN S/T Interface Controller(PCI總線的ISDN S/T接口控制器) |
| W6693A | USB Bus ISDN S/T Interface Controller(USB總線的ISDN S/T接口控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W6691CD | 制造商:WINBOND 制造商全稱:Winbond 功能描述:ISDN S/T Interface Transceiver |
| W6691CP | 制造商:WINBOND 制造商全稱:Winbond 功能描述:ISDN S/T Interface Transceiver |
| W6692 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:PCI Bus ISDN S/T-Controller |
| W6692A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:TE Mode S/T Controller with PCI 2.2 Interface and ACPT |
| W6692ACD | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:ISDN LINE INTERFACE|BASIC|CMOS|QFP|100PIN|PLASTIC |
發布緊急采購，3分鐘左右您將得到回復。