- 您現在的位置：買賣IC網 > PDF目錄363893 > W66910CD (WINBOND ELECTRONICS CORP) TE Mode ISDN S/T-Controller with Microprocessor Interface PDF資料下載
參數資料
| 型號： | W66910CD |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | 通信及網絡 |
| 英文描述： | TE Mode ISDN S/T-Controller with Microprocessor Interface |
| 中文描述： | SPECIALTY TELECOM CIRCUIT, PQFP100 |
| 封裝： | 14 X 20 MM, 1.40 MM HEIGHT, QFP-100 |
| 文件頁數： | 40/81頁 |
| 文件大小： | 681K |
| 代理商： | W66910CD |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁當前第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁
Data Sheet
W66910 PCI ISDN S/T-Controller
Publication Release Date:
Feb,2001
Revision 1.0
-40 -
The microprocessor may either enforce a 1 (idle state) in MR, MX by setting the control bit MRC or MXC (MOCR register) to 0,
or enable the control of these bits internally by the W66910 according to the Monitor channel protocol. Thus, before a data
exchange can begin, the control bit MRC, or MXC should be set to 1 by the microprocessor.
The relevant status bits are:
For the reception of Monitor data: MDR (Monitor Channel Data Received )
MER (Monitor Channel End of Reception)
For the transmission of Monitor data: MDA (Monitor Channel Data Acknowledged )
MAB (Monitor Channel Data
Abort)
About the status bit MAC( Monitor Channel Transmit Active) indicates whether a transmission is progress
.
If set MAC = 0,
the previous transmission has been terminated. Before starting a transmission, the microprocessor should
verify that the transmitter is inactive.
If set MAC = 1, after having written data into the Monitor Transmit Channel (MOX) register, the microprocessor sets this
bit to 1. This enables the MX bit to go active (0), indicating the presence of valid Monitor data (contents of MOX) in the
corresponding frame.
The receiving device stores the Monitor byte in its MOR (Monitor Receive Register) and generates a MDR (Monitor Channel
Data Receive) interrupt status. Alerted by the MDR interrupt, the microprocessor reads the MOR register. When it is ready to
accept data, it sets the MR control bit MRC to 1 to enable the receiver to store succeeding Monitor channel bytes and
acknowledge them according to the Monitor channel protocol. In addition, it enables other Monitor channel interrupts by setting
Monitor Channel Interrupt Enable to 1.
The first Monitor channel byte is acknowledged by the receiving device setting the MR bit to 0. This causes a MDA (Monitor
Channel Data Acknowledge) interrupt status at the transmitter. A new Monitor channel data byte can now be written by the
microprocessor in MOX register. The MX bit is still in the active (0) state. The transmitter indicates a new byte in the Monitor
channel by returning the MX bit active after sending it once in the inactive state. The receiver stores the Monitor channel byte in
MOR register and generates a new MDR interrupt status. When the microprocessor has read the MOR register , the receiver
acknowledges the data by returning the MR bit active after sending it once in the inactive state. This in turn causes the transmitter
to generate a MDA interrupt status. This
″
MDA interrupt
write data
MDR interrupt
read data
MDA interrupt
″
handshake procedure is repeated as long as the transmitter has data to send.
When the last byte has been acknowledged by the receiver (MDA interrupt status), the microprocessor sets the Monitor channel
Transmit Control bit MXC to 0. This enforces an inactive (1) state in the MX bit. Two frames of MX inactive signifies the end of
a message. Thus, a MER (Monitor channel End of Reception) interrupt status is generated by the receiver when the MX is
received in the inactive state in two consecutive frames. As a result, the microprocessor sets the MR control bit MRC to 0, which
in turn enforces an inactive state in the MR bit. This marks the end of the transmittion, making the MAC (Monitor channel
Active) bit return to 0.
During a transmission process, it is possible for the receiver to ask a transmission to be aborted by sending an inactive MR bit
value in two consecutive frames. This is effected by the microprocessor writing the MR control bit MRC to 0. An aborted
transmission is indicated by a MAB (Monitor Channel Data Abort) interrupt status at the transmitter.
7.9 8-bit Microprosessor Interface Circuit
At power up, the reset pin RST# must be asserted to initialize the chip. At rising edge of RST#, data value at CLK pin determines
the operation modes: HIGH for Intel bus mode, LOW for Motorola bus mode.
7.10 Peripheral Control
相關PDF資料 |
PDF描述 |
|---|---|
| W6691 | ISDN S/T Interface Transceiver |
| W6691CD | ISDN S/T Interface Transceiver |
| W6691CP | ISDN S/T Interface Transceiver |
| W6692 | PCI Bus ISDN S/T Interface Controller(PCI總線的ISDN S/T接口控制器) |
| W6693A | USB Bus ISDN S/T Interface Controller(USB總線的ISDN S/T接口控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W6691CD | 制造商:WINBOND 制造商全稱:Winbond 功能描述:ISDN S/T Interface Transceiver |
| W6691CP | 制造商:WINBOND 制造商全稱:Winbond 功能描述:ISDN S/T Interface Transceiver |
| W6692 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:PCI Bus ISDN S/T-Controller |
| W6692A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:TE Mode S/T Controller with PCI 2.2 Interface and ACPT |
| W6692ACD | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:ISDN LINE INTERFACE|BASIC|CMOS|QFP|100PIN|PLASTIC |
發布緊急采購，3分鐘左右您將得到回復。