国产精品成人VA在线观看-国产乱妇乱子视频在播放-国产日韩精品一区二区三区在线-国模精品一区二区三区

參數資料
型號: W83977TF
廠商: WINBOND ELECTRONICS CORP
英文描述: Multi-Function I/O Port Controller(用于個人計算機的多功能輸入/輸出口控制器)
中文描述: 多功能I / O端口控制器(用于個人計算機的多功能輸入/輸出口控制器)
文件頁數: 84/160頁
文件大小: 1012K
代理商: W83977TF
W83977TF
PRELIMINARY
Publication Release Date:March 1998
-74 -
Revision 0.62
7.2.2 Watch Dog Timer Output
Watch Dog Timer contains a one minute resolution down counter, CRF2 of Logical Device 8, and two
watch Dog control registers, WDT_CTRL0 and WDT_CTRL1 of Logical Device 8. The down counter
can be programmed within the range from 1 to 255 minutes. Writing any new non-zero value to
CRF2 or reset signal coming from a Mouse interrupt or Keyboard interrupt (CRF2 also contains non-
zero value) will cause the Watch Dog Timer to reload and start to count down from the new value. As
the counter reaches zero, (1) Watch Dog Timer time-out occurs and the bit 0 of WDT_CTRL1 will be
set to logic 1; (2) Watch Dog interrupt output is asserted if the interrupt is enable in CR72 of logical
device 8; and (3) Power LED starts to toggle output if the bit 3 of WDT_CTRL0 is enabled.
WDT_CTRL1 also can be accessed through GP2 I/O base address + 1.
7.2.3 Power LED
The Power LED function provides 1 Hertz rate toggle pulse output with 50 percent duty cycle. Table
7.2.2
shows how to enable Power LED.
Table
7.2.2
WDT_CTRL1 BIT[1]
WDT_CTRL0 BIT[3]
WDT_CTRL1 BIT[0]
POWER LED STATE
1
X
X
1 Hertz Toggle pulse
0
0
X
Continuous high or low *
0
1
0
Continuous high or low *
0
1
1
1 Hertz Toggle pulse
* Note: Continuous high or low depends on the polarity bit of GP13 or GP17
configuration
registers.
7.2.4 General Purpose Address Decoder
General Purpose Address Decoder provides two address decode as AEN equal to logic 0. The
address base is stored at CR62, CR63 of logical device 7
for GP14 and at CR62-65 of logical device
9 for GP32 and GP33
. The
decoding
output is normally active low. Users can alter its polarity
through the polarity bit of the GP14,
GP32, and GP33's
configuration register.
7.2.5 General Purpose Write Strobe
General Purpose Write Strobe is an address decoder that performs like General Purpose Address
Decoder, but it has to be qualified by IOW and AEN. Its output is normally active low. Users can
alter its polarity through the polarity bit of the GP15's configuration register.
相關PDF資料
PDF描述
W83C42 Keyboard Controller(鍵盤控制器)
W83C43 Keyboard Controller(鍵盤控制器)
W83C45 Keyboard Controller(鍵盤控制器)
W83C553F SYSTEM I/O CONTROLLER WITH PCI ARBITER
W83L177R 100MHZ 2-DIMM SDRAM BUFFER FOR NOTEBOOK
相關代理商/技術參數
參數描述
W83977TF(EOL) 制造商:未知廠家 制造商全稱:未知廠家 功能描述:W83877TF plus KBC. CIR. RTC
W83977TF_98 制造商:WINBOND 制造商全稱:Winbond 功能描述:WINBOND I/O
W83977TF-A 制造商:WINBOND 制造商全稱:Winbond 功能描述:I/O chip disk drive adapter
W83977TF-AW 制造商:WINBOND 制造商全稱:Winbond 功能描述:WINBOND I/O
W83977TF-P 制造商:WINBOND 制造商全稱:Winbond 功能描述:I/O chip disk drive adapter