- 您現在的位置：買賣IC網 > PDF目錄363904 > W89C940 (WINBOND ELECTRONICS CORP) ELANC-PCI (TWISTED-PAIR ETHER-LAN CONTROLLER WITH PCI INTERFACE) PDF資料下載
參數資料
| 型號： | W89C940 |
| 廠商： | WINBOND ELECTRONICS CORP |
| 英文描述： | ELANC-PCI (TWISTED-PAIR ETHER-LAN CONTROLLER WITH PCI INTERFACE) |
| 中文描述： | ELANC -的PCI（雙絞線醚局域網控制器帶有PCI接口） |
| 文件頁數： | 21/61頁 |
| 文件大小： | 353K |
| 代理商： | W89C940 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁
W89C940
21
Max-Lat Register
It is used for specifying how often the device needs to gain access to the PCI bus.
MAX_LAT is used to set the devices desired settings for Latency Timer values. The registers specify the values
in units of 0.25 microsecond. Zero means the device has no major requirements for the settings of Latency
Timer. The content of this register will be updated after power on by the EEPROM load operation. The Max-Lat
should be programmed into the 18th byte of the EEPROM for power on auto loading.
EEPROM PROGRAMMING FUNCTION
EEPROM Load and Reload procedure
A EEPROM control register(ECR) is used to control the operation mode of the EEPROM. The ECR is allocated
on the register address of page 3, 02H of LCE. The content of ECR is as following table:
BIT
SYMBOL
DESCRIPTION
0-5
Reserved
6
ERWS
EEPROM Read Write Select:
The write sequence to EEPROM is selected If ERWS = 1. If ERWS =
0, the read sequence is selected.
7
EAC
EEPROM Access Control:
EAC will enable the EEPROM read/write sequence if EAC = 1. The
EAS will be reset to " 0 " if the read/write sequence finished. Set EAC
= 0 will abort the EEPROM read/write sequence immediately.
The read/write sequence for EEPROM is described as following two statements.
Write Sequence:
write(ECR with ERWS=1 and EAC=1); /* enable the write sequence */
write(BFR, address); /* specify the address in which the data will be modified */
write(BFR, word_data); /* specify the data which will be write into the EEPROM */
repeat( read(ECR.EAC); ) until (EAC=0); /* wait for the programming process completed */
File2
Any operation that violate the write sequence will cause the EEPROM programming process aborted. The BFR
is a buffer register located at the register address of page3, 04H of LCE. With the EEPROM load back
sequence specified above, the contents at the specified address will be overwritten by the new data. One word
of data is modified by each write sequence. The allowable address in which the content will be modified is from
00H to 3fH.
Read Sequence:
write(ECR with ERWS=0 and EAC=1); /* enable the read sequence */
write(BFR, address); /* specify the address in which the data will be read out */
repeat( read(ECR.EAC); ) until (EAC=0); /* wait for the reading process completed */
read(BFR);
/* read word data */
相關PDF資料 |
PDF描述 |
|---|---|
| W89C982 | INTEGRATED MULTIPLE REPEATER II |
| W89C982AF | INTEGRATED MULTIPLE REPEATER II |
| W8NB80 | N - CHANNEL 800V - 1.2ohm - 7.5A - TO-247 PowerMESH MOSFET |
| W90100F | Embedded Micro-Controller(32位嵌入式的微控制器) |
| W90210F | PA-RISC Embedded Micro-Controller(惠普PA-RISC結構的32位嵌入式微控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W89C940F | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:10M PCI-Bus Ethernet Network Interface Controller |
| W89C982 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:INTEGRATED MULTIPLE REPEATER II |
| W89C982AF | 制造商:WINBOND 制造商全稱:Winbond 功能描述:INTEGRATED MULTIPLE REPEATER II |
| W8C2-DNL | 制造商:Hwei Lung Precision Machinery 功能描述:TORCH 8 LED BLACK 2C |
| W8D10PF29033 | 制造商:TE Connectivity 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。