- 您現在的位置：買賣IC網 > PDF目錄363904 > W89C940 (WINBOND ELECTRONICS CORP) ELANC-PCI (TWISTED-PAIR ETHER-LAN CONTROLLER WITH PCI INTERFACE) PDF資料下載
參數資料
| 型號： | W89C940 |
| 廠商： | WINBOND ELECTRONICS CORP |
| 英文描述： | ELANC-PCI (TWISTED-PAIR ETHER-LAN CONTROLLER WITH PCI INTERFACE) |
| 中文描述： | ELANC -的PCI（雙絞線醚局域網控制器帶有PCI接口） |
| 文件頁數： | 23/61頁 |
| 文件大小： | 353K |
| 代理商： | W89C940 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁
W89C940
23
Since the ELANC-PCI reloads data into the configuration registers each time the system is reset, caution should
be taken in handling resets. A system reset should keep low at least 480ns for the ELANC-PCI to decode the
action as a reset. Any signal on the RESET pin shorter than this will be interpreted as noise and no response
will be taken by the ELANC-PCI.
After the reset signal is recognized, the ELANC-PCI to read configurations and ID contents from the EEPROM.
The read clock is sent by the ELANC-PCI to the EEPROM. Normally the period of the clock is 1.2
μ
S. The
ELANC-PCI will serially generate the EEPROM address so that the configuration and ID
After the reset signal is recognized, the ELANC-PCI to read configurations and ID contents from the EEPROM.
The read clock is sent by the ELANC-PCI to the EEPROM. Normally the period of the clock is 1.2
μ
S. The
ELANC-PCI will serially generate the EEPROM address so that the configuration and ID will be read into the
internal register file of W89C940.
NETWORK STATUS LED DISPLAY FUNCTION
Network Segment Status LED Display
Network activity displaying. ACT will indicate the network activity status by three types of signals (DC0 DC1
and AC 10Hz).
DC 0 : indicating "Link Good", if UTP is selected.
DC 1 : indicating 1) "Link fail", if UTP is selected.
2) "idle", if AUI is selected.
AC 10Hz : indicating the DTE is transmitting a packet or the carrier on the network is detected by the
transceiver and the carrier sense signal is received by W89C940.
The ACT will keep DC 1 if there is an abnormal network collision occurred, e.g. the transceiver collision signal
always active.
UTP OR COAXIAL AUTO-SELECTION FUNCTION
Auto Media-Switching
The ELANC-PCI provides a UTP/BNC auto media-switching function. The physical interface will jump from UTP
to BNC when the ELANC-PCI is configured as UTP, link checking is enabled, and the current UTP path is
broken. It will jump back immediately after the UTP path has been reconnected. When the physical interface is
configured as BNC or AUI, this auto media-switching function will be disabled.
at least
EEREAD
RST#
1usec
1usec
14.4usec
相關PDF資料 |
PDF描述 |
|---|---|
| W89C982 | INTEGRATED MULTIPLE REPEATER II |
| W89C982AF | INTEGRATED MULTIPLE REPEATER II |
| W8NB80 | N - CHANNEL 800V - 1.2ohm - 7.5A - TO-247 PowerMESH MOSFET |
| W90100F | Embedded Micro-Controller(32位嵌入式的微控制器) |
| W90210F | PA-RISC Embedded Micro-Controller(惠普PA-RISC結構的32位嵌入式微控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W89C940F | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:10M PCI-Bus Ethernet Network Interface Controller |
| W89C982 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:INTEGRATED MULTIPLE REPEATER II |
| W89C982AF | 制造商:WINBOND 制造商全稱:Winbond 功能描述:INTEGRATED MULTIPLE REPEATER II |
| W8C2-DNL | 制造商:Hwei Lung Precision Machinery 功能描述:TORCH 8 LED BLACK 2C |
| W8D10PF29033 | 制造商:TE Connectivity 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。