国产精品成人VA在线观看-国产乱妇乱子视频在播放-国产日韩精品一区二区三区在线-国模精品一区二区三区

參數資料
型號: W90210F
廠商: WINBOND ELECTRONICS CORP
元件分類: 微控制器/微處理器
英文描述: PA-RISC Embedded Micro-Controller(惠普PA-RISC結構的32位嵌入式微控制器)
中文描述: 32-BIT, MROM, RISC MICROCONTROLLER, PQFP208
封裝: PLASTIC, QFP-208
文件頁數: 22/67頁
文件大小: 297K
代理商: W90210F
W90210F
22
Version 1.4, 10/8/97
The above information is the exclusive intellectual property of Winbond Electronics Corp. and shall not be disclosed, distributed or reproduced without permssion fromWinbond.
6. Pipeline Architecture
The pipeline used in the W90210F CPU core is a typical five-stage pipeline. Most instructions are executed in
one single cycle except long instructions. Long instructions are FDC, FDCE, FIC, FICE, PDC, RFIR, and RFI. For
Branch instruction, one delay slot is needed.
The pipeline is shown below:
CLK
CLK
CLK
CLK
CLK
CLK
CLK
IA
IF
FR
EX
MM
WB
IA
IF
FR
EX
MM
WB
IA
IF
FR
EX
MM
WB
IA:
Instruction address calculation
IF:
Instruction fetch
FR:
Register fetch and decode
EX:
Execution and data address calculation
MM:
Memory reference for Load/Store instruction
WB:
Write back to register file
Figure 6.1 W90K pipeline architecture
IA:
The instruction address for the cycle is generated. The sources of the instruction address are n+1, branch
target, interrupt vector, IIAOQ, and reset pointer. The address is calculated and selected within half cycle.
IF:
Instruction cache is fetched during this cycle. Instruction will be available before end of IF. IMISS (instruction
cache miss) will be available at the second half of IF.
FR:
The instruction from IF stage is used to access the register file and decoded for execution. The bypass
control is also generated to select the correct bypass path. If the instruction is a cache miss, the pipeline will stall at this
stage.
EX:
The instruction is executed in this stage. For branch instructions, a dedicated adder is used to calculate the
target address at the first half of EX (corresponding to the IA stage of the instruction after the delay slot). The condition
check is also performed in this stage for conditional branch instruction. Data address for memory reference instruction is
also calculated in this stage. For non-nullified MTCTL instruction, data will be written into CR at the end of the EX stage.
External traps (EI, HPMC, LPMC and PFW) will be sampled at the EX stage and piped to the WB stage for trap
handling.
MM:
The data cache is referenced at this stage.
WB:
The data from EX or MM stage will be written back to register file in the first half of the WB stage. The data
can be read out by the FR stage in the same cycle; otherwise one extra bypass will be needed. If the MM stage of this
instruction is a miss and a data dependence exists, the pipeline will stall at the WB stage; otherwise, the pipeline will
continue.
6.1 Branch prediction
Static branch prediction is used for conditional branch instructions in W90210F CPU core.
Forward branch: predict not taken
Backward branch:predict taken
相關PDF資料
PDF描述
W90220F PA-RISC Embedded Micro-Controller(惠普PA-RISC結構的32位嵌入式微控制器)
W90221F PA-RISC Embedded Micro-Controller(惠普PA-RISC結構的32位嵌入式微控制器)
W91030B Low Power CMOS IC For Caller indentification(用于通信中呼叫確認的低功耗CMOS集成電路芯片)
W91030 Low Power CMOS IC For Caller indentification(用于通信中呼叫確認的低功耗CMOS集成電路芯片)
W91031 LOW POWER CMOS INTERGRATED CIRCUIT
相關代理商/技術參數
參數描述
W902E31 制造商:Omron Corporation 功能描述:
W903B-28C 制造商: 功能描述: 制造商:undefined 功能描述:
W903B48D 制造商: 功能描述: 制造商:undefined 功能描述:
W905 制造商:LUMINIS 制造商全稱:LUMINIS 功能描述:Post top mount
W9050B016 制造商:Pulse Electronics Corporation 功能描述:1.13OD 1.6'' I-Pex to I-Pex Cable Assembly